Description

Automatic Block Machine Paver Machine Tuff Tile Machine Hydraulic Technology

Automatic Block Making Machine Price in Pakistan – SSM 15, 18, 24, 28, 35 & 50

Looking for an automatic block making machine in Pakistan for concrete blocks, hollow blocks, solid blocks, interlocking pavers, tuff tiles, kerbstones or concrete bricks? Silver Steel Mills manufactures and supplies a range of SSM block-making systems, from smaller semi-automatic production machines to fully automatic industrial plants.

This guide explains the automatic block making machine price in Pakistan, machine specifications, mould selection, product sizes, hydraulic pressing, vibration, batching, mixing, pallet handling, production capacity, electrical requirements and the difference between SSM 15, SSM 18, SSM 24, SSM 28, SSM 35 and SSM 50.

Important: The final machine price and production output depend on the selected model, mould, product dimensions, cycle time, concrete mix, batching/mixing system, automation level and included accessories. Request a project-specific quotation before purchasing.

Automatic Block Making Machine Price in Pakistan

The price of an automatic block making machine in Pakistan is not determined by the machine name alone. A buyer may compare two machines that look similar but have very different hydraulic systems, vibration power, mould construction, batching equipment, pallet handling and automation.

For this reason, Silver Steel Mills recommends comparing the complete production system rather than only comparing the advertised price of the main block machine.

Machine	Production Position	Automation	Typical Use	Price
SSM 15	Entry / commercial	Semi-automatic configuration	Small and growing block or paver business	Request current quotation
SSM 18	Commercial	Semi-automatic configuration	Growing production and fly-ash/brick applications	Request current quotation
SSM 24	High production	Automatic	Pavers, tuff tiles, blocks and coloured products	Request current quotation
SSM 28	Large production	Automatic	Integrated block/paver production plant	Custom quotation
SSM 35	Industrial	Fully automatic	Large commercial factories and projects	Request current quotation
SSM 50	Mega industrial	Fully automatic	High-volume block and paver production	Custom quotation

Why is there no permanent single price?
A machine supplied with one mould and basic handling equipment is not equivalent to a complete plant containing automatic batching, planetary mixer, conveyors, colour/topping system, pallet conveyor and automatic stacker. Always compare the complete scope of supply.

What Is an Automatic Block Making Machine?

An automatic block making machine is a hydraulic and vibration-based production system used to manufacture moulded concrete products with controlled material feeding, compaction and product handling.

Depending on the selected configuration, the complete production line can contain:

Aggregate Batching Sand, crush and other aggregates are measured according to the selected production recipe.

Concrete Mixing The batched ingredients are mixed to obtain a consistent moulding material.

Material Transfer Conveyors, buckets or other transfer systems move the prepared material toward the block machine.

Hydraulic Compaction Hydraulic pressure helps compress the material inside the mould.

High-Frequency Vibration Vibration helps distribute and compact the relatively dry concrete mix inside the mould.

Pallet Handling Automatic systems can transfer, move and stack green products on production pallets.

How an Automatic Block Machine Actually Makes a Block

Raw Material Preparation

The production starts with cement, sand, crush/aggregate, water and any approved admixture or pigment required by the selected product. For fly-ash or special products, the recipe is developed around the required raw material characteristics.

Batching and Weighing

For an integrated plant, aggregates can be stored in separate bins and measured according to the production recipe. Accurate batching helps maintain repeatability from one production cycle to another.

Mixing

The measured material enters the mixer. The objective is to distribute cement and moisture consistently throughout the aggregate mixture without making the mix unnecessarily wet.

Feeding the Mould

The prepared concrete is transferred to the machine's feed system. The mould determines the shape, dimensions and number of products that can be formed in each cycle.

Vibration and Hydraulic Pressing

The machine applies vibration and hydraulic compaction. These two actions work together: vibration helps the particles settle while the hydraulic system applies controlled forming pressure.

Moulding

The concrete takes the geometry of the selected mould. The same machine can therefore manufacture different products when compatible moulds and machine settings are used.

Demoulding

After the moulding cycle, the newly formed green products remain on the production pallet. The product is not yet at its final cured strength.

Transfer and Stacking

Depending on the machine line, conveyors, pallet handling and stackers can move the green products to the curing/stockyard area.

Curing

The products must be cured under the appropriate conditions before being sold or placed into service. Final strength depends on the cementitious system, aggregate, water/cement relationship, compaction, curing regime and product geometry.

SSM Automatic Block Making Machine Models

Silver Steel Mills offers different SSM configurations because a customer producing a few thousand blocks per day has very different requirements from a large paver factory supplying housing schemes or infrastructure projects.

ENTRY / COMMERCIAL PRODUCTION

SSM 15 Automatic / Semi-Automatic Block & Paver Machine

The SSM 15 block making machine is intended for customers who want to enter commercial concrete-product manufacturing without immediately investing in the largest industrial plant.

It can be configured for compatible moulds used for pavers, blocks, bricks and other moulded concrete products. The SSM 15 is particularly relevant where production flexibility, manageable investment and relatively compact plant requirements are important.

Automatic/semi-automatic production configuration.
Suitable for blocks, pavers and other compatible moulded products.
Auto-pallet handling configuration available.
Hydraulic pressing and vibration-based forming.
Compatible mould depth depends on the selected configuration.
Suitable for small and growing construction-material businesses.

Best for: new block businesses, local paver producers, small housing projects and customers who want to increase production beyond basic manual machinery.

GROWING BUSINESS

SSM 18 Block & Brick Making Machine

The SSM 18 sits above the entry-level production category and can be selected where the customer needs more output or wants a machine configuration suited to specific brick/block production requirements.

The machine can be configured around the product mould and raw-material recipe. For customers working with fly ash, biomass ash or other alternative mineral materials, the complete recipe and moulding requirements should be tested before final production specifications are confirmed.

SSM 18 Suitable Products

Concrete blocks.
Solid blocks.
Fly ash bricks where the selected mould and mix are suitable.
Pavers and compatible paving products.
Custom moulded concrete products.

Best for: growing block manufacturers, brick producers, contractors and customers who need more production capacity than a small starter setup.

AUTOMATIC DOUBLE-LAYER PRODUCTION

SSM 24 Automatic Paver, Block & Tuff Tile Machine

The SSM 24 is a higher-production automatic system and is particularly useful where the customer wants to manufacture pavers, tuff tiles, blocks and coloured paving products.

A published SSM 24 configuration includes a 30 HP hydraulic power unit, 2-bag concrete mixer, 1-bag colour mixer, separate concrete and colour/topping conveyors, aggregate and colour hoppers, a 20-foot pallet chain conveyor and pallet stacker.

SSM 24 Component	Published Configuration
Machine type	Double-layer block, paver and tuff tile plant
Hydraulic motor	30 HP, 1400 RPM configuration
Concrete mixer	2 cement-bag capacity configuration
Colour mixer	1 cement-bag capacity configuration
Concrete conveyor	3 HP motor & gear configuration
Colour/topping conveyor	3 HP motor & gear configuration
Pallet conveyor	20 ft chain conveyor configuration
Pallet stacker	Automatic stacker configuration
Wooden pallet	30 × 42 inch published configuration
Hydraulic oil	Approximately 600 L in documented configuration

The final machine configuration should be confirmed in the quotation because accessories, moulds, batching equipment and electrical scope can vary.

LARGE AUTOMATIC PLANT

SSM 28 Automatic Block Making Machine & Complete Plant

The SSM 28 is positioned for customers moving toward a larger automatic production setup. It is particularly relevant when the buyer wants the block machine to work as part of a complete line rather than operating as a standalone press.

A complete SSM 28 project can be developed around:

Automatic aggregate batching.
Concrete mixing.
Material conveyors.
Hydraulic block/paver forming.
Production pallets.
Automatic handling.
Stacking equipment.
Selected product moulds.
Electrical/control system.

Because SSM 28 can be specified according to the required plant configuration, the production capacity and price should be confirmed from the customer's exact product, mould and automation requirement rather than copied from another machine.

INDUSTRIAL FLAGSHIP

SSM 35 Fully Automatic Hydraulic Block Making Machine

The SSM 35 is designed for industrial-scale concrete product manufacturing. It is suitable for factories that need higher production capacity and reduced manual handling.

Parameter	SSM 35 Published Configuration
Machine type	Fully automatic hydraulic block machine
Control	PLC touchscreen control
Hydraulic pressure	Up to 300 tons
Hydraulic motor	30 HP published configuration
Vibration	Dual high-frequency vibration motors
Vibration motors	20 HP × 2 published configuration
Cycle	Approximately 15–20 seconds depending on product/configuration
Pallet	889 × 1219 × 38 mm published configuration
Product height	Approximately 50–200 mm in published configuration
Mould	Heat-treated/alloy steel according to product requirement
Products	Blocks, pavers, tuff tiles and kerbstones
Batching	Automatic batching system available
Mixer	Planetary mixer configuration available
Stacking	Automatic pallet stacker available

The SSM 35 can be supplied as a complete production line with batching, mixer, conveyor, pallet handling and stacker. The actual output should always be specified against the selected mould and product, because a paver, hollow block and solid brick do not have the same cavity count, volume or cycle requirements.

MEGA INDUSTRIAL PRODUCTION

SSM 50 Fully Automatic Block & Paver Making Plant

The SSM 50 is the high-capacity model in the SSM range for customers requiring large-scale production of blocks, pavers, tuff tiles, kerbstones and other compatible moulded concrete products.

SSM 50 Specification	Published Configuration
Machine type	Fully automatic mega industrial block machine
Production	Up to 50,000+ pavers/tiles per day*
6-inch hollow blocks	Up to 15,000+ blocks/day*
Hydraulic system	Heavy-duty hydraulic system
Hydraulic pressure	Up to 400 tons in published configuration
Vibration	High-frequency servo/dual vibration configuration
Vibration speed	Up to approximately 5,500 RPM in published configuration
Control	PLC automatic control with touchscreen interface
Batching	Automatic multi-bin aggregate batching
Aggregate bins	Up to 5 bins
Mixer	Heavy-duty planetary mixer
Mixer capacity	Up to approximately 2,000 kg configuration
Conveyor	Approximately 15 m × 1,200 mm published configuration
Pallet handling	Automatic handling/stacking system

*Actual production varies with mould, product dimensions, mix design, cycle time, pallet arrangement, raw material and operating conditions.

What Products Can an Automatic Block Machine Make?

One of the biggest advantages of a mould-based hydraulic block machine is product flexibility. The machine does not permanently manufacture only one shape. The mould is the primary component that defines the product geometry.

Hollow Concrete Blocks Used for masonry walls and partition construction. Common moulds include 4-inch, 6-inch and 8-inch configurations, subject to the machine and mould design.

Solid Concrete Blocks Suitable for applications requiring a solid molded masonry unit.

Interlocking Pavers Machines can be configured with moulds for zigzag, I-shape, rectangular and other interlocking patterns.

Tuff Tiles Paving products can be manufactured in different thicknesses and surface patterns according to the mould.

Kerbstones Kerb moulds can be selected for roads, parking areas, landscaping and infrastructure works.

Concrete Bricks Suitable moulds can be used for brick-shaped concrete products where the required dimensions and recipe are compatible.

Block Making Machine Mould Sizes – Why Mould Selection Matters

When a customer asks, “Which block machine should I buy?”, the more useful question is often, “Which products do you want to manufacture?”

A machine may have a high hydraulic capacity but still require the correct mould arrangement to achieve the desired output. Product height, length, width, cavity geometry and number of cavities per cycle all affect production.

Product	Common Planning Dimensions	Typical Mould Consideration
4-inch hollow block	Approx. 100 mm wall thickness class	Hollow cavity geometry and height must match machine
6-inch hollow block	Approx. 150 mm wall thickness class	Higher material volume than smaller block
8-inch hollow block	Approx. 200 mm wall thickness class	Larger mould volume and different cavity arrangement
Solid block	Product-specific	Solid cavity/plate geometry
60 mm paver	60 mm thickness class	Suitable paver mould and topping configuration where required
80 mm paver	80 mm thickness class	Higher product volume than 60 mm paver
100 mm paver	100 mm thickness class	Machine/mould height compatibility required
Kerbstone	Project-specific	Dedicated kerb mould usually required

Do not order the mould by name only. Send the exact product drawing or dimensions. Length × width × height, cavity arrangement, desired production per cycle and pallet size should be checked before mould fabrication.

Paver Mould and Double-Layer Tuff Tile Production

For coloured interlocking pavers and tuff tiles, the moulding system can be combined with a second material layer or colour-topping arrangement. The base concrete provides the main body of the product while a selected surface material can create the finished face.

This is particularly important for decorative paving products because the customer may require a different aggregate, pigment, texture or surface finish for the top layer.

Typical Double-Layer Sequence

Prepare the base concrete mix.
Prepare the topping/face mix separately.
Transfer the base material into the mould.
Place the face/topping material according to the selected system.
Apply vibration and compaction.
Demould onto the production pallet.
Move the green pavers to the curing area.

The exact colour mixer, topping hopper and conveyor arrangement depends on the selected machine configuration. The SSM 24 published configuration, for example, includes separate concrete and colour mixing/feeding equipment. :contentReference[oaicite:3]{index=3}

Hydraulic Pressure vs Vibration – Both Matter

Customers sometimes compare machines only by hydraulic tonnage. Hydraulic pressure is important, but it is not the only factor controlling the quality of a concrete product.

The final product depends on the combined effect of:

Concrete mix design.
Aggregate grading.
Moisture content.
Cement content.
Mould geometry.
Hydraulic compaction.
Vibration frequency and amplitude.
Cycle time.
Pallet stability.
Demoulding technique.
Curing conditions.

A higher-tonnage hydraulic system does not automatically mean that every product will achieve a particular PSI. Strength must be established through an appropriate mix design, production process and testing program.

How Mould Design Affects Production Capacity

Suppose a paver mould produces 15 pieces per cycle while a block mould produces 6 or 8 larger units. Even if the machine cycle time remains similar, the number of finished products per hour will be different.

Therefore, a machine advertised as “35,000 pieces/day” should always be evaluated against the exact product being discussed.

For accurate production planning, calculate:

Production per hour ≈ Products per cycle × 3600 ÷ cycle time in seconds

Then adjust for practical production losses, material supply, mould filling, pallet handling, operator breaks, maintenance and curing/handling constraints.

Example: Why Product Size Changes Output

A 60 mm paver occupies considerably less mould volume than a 200 mm-high hollow block. The mould may therefore hold more paving units than large masonry units during one production cycle.

This is why Silver Steel Mills should quote production capacity against a defined product instead of giving one number that is assumed to apply equally to pavers, hollow blocks and solid bricks.

Automatic Batching Plant for Block Machine

For a commercial or industrial factory, the batching system can be as important as the block machine itself. If the operator manually measures every aggregate load, the mix may vary from batch to batch.

An automatic batching system can use individual bins and weighing arrangements to control the quantity of different aggregates before they enter the mixer.

Typical Batching Plant Components

Aggregate storage bins.
Weighing system/load cells.
Aggregate gates.
Conveyor or bucket transfer.
Cement feeding arrangement.
Water dosing.
Control panel.
Mixer.

Planetary Mixer vs Conventional Mixer

The mixer must be selected according to the concrete product and required production rate. A high-output block plant needs a mixer that can supply the block machine at a rate that does not become the bottleneck.

Planetary mixers are commonly considered for dry concrete product manufacturing because the mixing action is designed to distribute cement, aggregate and moisture efficiently. The final choice should be based on the machine line, recipe and production target.

Automatic Pallet Handling System

Pallet handling becomes increasingly important as production increases. If workers manually move every green product pallet, the block machine may produce faster than the downstream handling team can manage.

A more automated plant can include:

Automatic pallet dispenser.
Pallet chain conveyor.
Transfer conveyor.
Green product handling.
Automatic pallet stacker.
Return pallet system.

The purpose is to keep the moulding cycle supplied with empty pallets and move finished green products away from the machine without creating a production bottleneck.

Electrical Power Requirement

Electrical requirements depend heavily on the complete plant configuration. The main block machine, hydraulic power unit, vibration motors, mixer, conveyors, batching system, stacker and pumps all contribute to the connected load.

For example, published SSM configurations show materially different electrical requirements between SSM 24 and SSM 35. This is why the customer's available three-phase supply should be checked before finalizing the plant.

Before installation: confirm transformer capacity, incoming voltage, cable sizing, protection equipment, earthing, motor starting arrangements and available three-phase power with the machine supplier and qualified electrical engineer.

Factory Space Required for an Automatic Block Machine

The required area is not simply the footprint of the block machine.

A practical production site needs space for:

Aggregate storage.
Batching plant.
Mixer.
Block machine.
Pallet movement.
Green-product handling.
Curing area.
Finished-product stockyard.
Truck loading.
Maintenance access.
Worker circulation.

A complete SSM 35 line has previously been described with a much larger overall plant area than the machine footprint alone. The exact site layout should therefore be prepared before construction begins.

Concrete Mix Design for Blocks and Pavers

The machine does not create strength by itself. The raw material recipe and curing process are equally important.

A typical concrete-product recipe may contain:

Cement.
Fine aggregate/sand.
Crushed aggregate according to product requirement.
Water.
Approved pigment for coloured face mix.
Admixture where required.

For a specific product, the mix should be developed according to the required strength, workability, density, aggregate grading and curing conditions.

Why Moisture Control Is Important

Block and paver machines generally work with relatively stiff concrete mixes compared with conventional wet-cast concrete. If the mix is too dry, it may not compact or hold the mould shape properly. If it is too wet, demoulding and product stability can become difficult.

The correct moisture level therefore has to be established through controlled trials for the selected aggregates and mould.

Block Strength – What Actually Determines PSI?

A machine specification may mention hydraulic pressure, but the final compressive strength of the finished block is a product of the complete manufacturing process.

Factor	Effect on Product
Cement content	Affects cementitious bonding and potential strength
Aggregate quality	Influences density and structural performance
Water content	Strongly affects workability and final properties
Compaction	Helps reduce unwanted voids and improve density
Vibration	Helps material settle into the mould
Mould geometry	Controls product dimensions and wall/cavity arrangement
Curing	Critical for cement hydration and strength development
Testing	Confirms actual product performance

How Long Does an Automatic Block Machine Last?

Machine life depends on fabrication quality, steel structure, hydraulic maintenance, vibration components, lubrication, mould wear, operating hours and availability of replacement parts.

The most heavily used components should be treated as wear or maintenance items. Moulds, vibration components, hydraulic seals and other consumable/wear components may require replacement during the machine's operating life.

For a production business, after-sales support and availability of spare parts should therefore be considered before purchase.

Mould Wear and Maintenance

The mould is one of the most important precision components of a block machine. It repeatedly contacts abrasive concrete materials and is exposed to vibration and mechanical loading.

Mould life depends on:

Steel quality.
Heat treatment.
Aggregate abrasiveness.
Product cycle count.
Cleaning procedure.
Alignment.
Lubrication where specified.
Operator handling.

When a mould becomes worn, product dimensions, corners and surface quality can gradually change. Regular inspection therefore protects production consistency.

Changing the Mould – Why It Requires Technical Setup

Changing from a paver mould to a taller hollow-block mould is not simply a matter of removing four bolts and inserting another mould. The machine's working height, mould support, alignment and upper forming components must match the new product.

For example, the published SSM 35 mould-change material describes a difference between a 60 mm paver configuration and a 200 mm hollow-block configuration, requiring machine-height adjustment and careful alignment.

Important safety point: Never work underneath an unsupported vibration/motor assembly. Use the machine's mechanical locking or approved support arrangement during mould change and maintenance.

Automatic vs Semi-Automatic Block Machine

Feature	Semi-Automatic	Fully Automatic
Initial investment	Usually lower	Usually higher
Manual intervention	Higher	Lower
Production scale	Small to medium	Medium to industrial
Batching integration	Optional depending on setup	Can be integrated
Pallet handling	Partly manual depending on configuration	Can be automated
Labour requirement	Generally higher	Generally lower for equivalent production
Best for	Startups and growing businesses	High-volume production

How to Select the Right SSM Block Machine

Choose SSM 15 If your production target is relatively small and you want a practical entry into commercial block/paver manufacturing.

Choose SSM 18 If your business is growing and you need more production flexibility or a configuration suited to brick/block applications.

Choose SSM 24 If your business focuses on pavers, tuff tiles, coloured products and higher production.

Choose SSM 28 If you need a larger automated production setup and want the plant designed around your output target.

Choose SSM 35 If you require an industrial-scale automated plant with integrated batching, mixing and handling options.

Choose SSM 50 If your business needs very high production capacity and a complete industrial block/paver manufacturing line.

What Is Included in a Complete Automatic Block Making Plant?

The scope can vary from one quotation to another. A complete plant may include:

Equipment	Function
Block making machine	Main hydraulic moulding and vibration system
Mould	Determines product shape and dimensions
Batching plant	Measures aggregates/materials
Mixer	Prepares homogeneous concrete mix
Concrete conveyor	Transfers material
Colour mixer	Prepares decorative face mix where required
Colour conveyor	Transfers topping material
Pallet conveyor	Moves production pallets
Pallet stacker	Handles finished green-product pallets
PLC/control panel	Controls machine sequence

Automatic Block Machine Installation Process

Factory Layout

Prepare the machine line layout showing batching, mixer, conveyor, block machine, pallet movement and stockyard.

Civil Foundation

Construct the required machine and equipment foundations according to the approved layout and equipment loads.

Machine Positioning

Position the block machine, batching equipment, mixer and conveyors accurately.

Electrical Installation

Connect the control system, motors, protection equipment and required three-phase electrical supply.

Hydraulic Commissioning

Check hydraulic oil, pressure system, hoses, pumps, valves and operating sequence.

Mould Installation

Install and align the selected mould according to the product dimensions and machine configuration.

Dry Trial

Run the mechanical sequence without production material to confirm movement, sensors, conveyors and safety functions.

Production Trial

Introduce the concrete mix and produce trial units. Adjust filling, vibration, compaction and cycle settings as required.

Operator Training

Train operators on machine operation, mould change, cleaning, lubrication, basic troubleshooting and safety procedures.

Automatic Block Machine Maintenance

A production machine should be maintained as a production asset, not repaired only after a breakdown. Preventive maintenance reduces avoidable downtime and helps maintain product consistency.

Daily Checks

Hydraulic oil level.
Visible hydraulic leaks.
Machine bolts and fasteners.
Mould cleanliness.
Vibration motor condition.
Conveyor operation.
Electrical panel indicators.
Emergency stop and safety controls.

Periodic Checks

Hydraulic filters and oil condition.
Motor bearings.
Vibration components.
Conveyor bearings and chains.
Mould wear.
Hydraulic hoses and seals.
Electrical terminals.
PLC/sensor connections.

Common Problems in Block Production

Problem	Possible Cause	What to Check
Block corners breaking	Mix, demoulding, mould wear or handling	Moisture, compaction, mould and curing
Different block density	Inconsistent batching or moisture	Recipe and aggregate moisture
Weak pavers	Mix/curing/compaction problem	Mix design, vibration and curing
Uneven product height	Mould or machine alignment	Mould level and machine settings
Machine vibration abnormal	Mechanical/electrical issue	Vibration motors and mounting
Hydraulic pressure unstable	Hydraulic system issue	Oil, pump, valves, seals and pressure settings

What to Ask Before Buying a Block Making Machine in Pakistan

Before paying for a machine, ask the manufacturer for a written technical quotation covering the complete scope.

Which exact model is being supplied?
What product will the quoted output be based on?
What mould size is included?
How many pieces are produced per cycle?
What is the approximate cycle time?
What hydraulic system is included?
How many vibration motors are included?
Is batching included?
Is the mixer included?
Are conveyors included?
Is automatic pallet handling included?
Is the stacker included?
How many moulds are included?
What electrical load is required?
What civil foundation is required?
What installation support is included?
What operator training is included?
What warranty terms apply?
What spare parts are available?

Why Local Manufacturing Matters in Pakistan

For industrial machinery, the purchase price is only one part of the investment. When a machine is used every working day, the ability to obtain technical assistance, replacement parts, moulds, hydraulic components and fabrication support can affect the overall operating cost.

Silver Steel Mills manufactures its SSM machinery in Pakistan and operates from Lahore. This allows Pakistani customers to discuss machine modifications, mould requirements and production applications directly with the manufacturer rather than relying only on an overseas distributor.

Automatic Block Machine for Different Business Models

Block Manufacturing Business Produce hollow and solid blocks for local contractors, builders and housing projects.

Paver Factory Produce interlocking pavers and decorative paving products for residential and commercial projects.

Tuff Tile Business Use suitable mould and topping systems for coloured and decorative paving.

Housing Scheme Set up captive production where large quantities of blocks or pavers are needed.

Contractor Plant Manufacture products for your own construction projects instead of buying all material externally.

Large Infrastructure Plant Use higher-capacity automatic systems where production volume justifies the investment.

Automatic Block Machine Price vs Complete Plant Cost

This distinction is extremely important when calculating the investment.

The machine price may refer only to the main block-making unit, while the complete plant cost can include batching, mixer, conveyors, moulds, pallets, stacker, electrical system, installation, civil work and other accessories.

A serious buyer should therefore calculate the complete project investment:

Total Plant Investment = Machine + Moulds + Batching + Mixer + Conveyors + Pallets + Stacker + Electrical Work + Civil Work + Installation + Transport + Initial Raw Material + Working Capital

How to Calculate Your Block Machine Production Target

Start with your sales requirement instead of starting with machine capacity.

For example, if your customers require 8,000 hollow blocks per day, buying a machine capable of producing tens of thousands of pavers per day may not automatically be the most economical decision. On the other hand, if you have contracts requiring large quantities of pavers every day, a smaller machine may become a production bottleneck.

The correct machine is the one whose practical production capability matches your expected sales, available capital, labour, space and future growth.

SSM Block Machine Product Selection Guide

Your Requirement	Suggested Direction
Starting a small commercial unit	Evaluate SSM 15
Growing block/brick business	Evaluate SSM 18
High-volume paver/tuff tile production	Evaluate SSM 24
Integrated automatic plant	Evaluate SSM 28
Industrial production	Evaluate SSM 35
Mega-scale production	Evaluate SSM 50

Request an Automatic Block Machine Quotation

For an accurate quotation, do not send only the message “automatic block machine price?” Send the product you want to manufacture and your expected production target.

Send these details:

Product: hollow block / solid block / paver / tuff tile / brick / kerbstone.
Product size: length × width × height.
Target daily production.
Required automation level.
Number of moulds required.
Factory location.
Available factory area.
Available electrical supply.
Whether batching plant is required.
Whether mixer is required.
Whether automatic stacker is required.
Whether installation and training are required.

Buy an Automatic Block Making Machine From Silver Steel Mills

If you are planning a block, paver, tuff tile or concrete-brick manufacturing business in Pakistan, Silver Steel Mills can help you select the machine according to your product and production target.

SSM 15 • SSM 18 • SSM 24 • SSM 28 • SSM 35 • SSM 50

Tell us your product size, required daily production, factory location and budget. We can then recommend the appropriate machine configuration, mould and production-line scope.

Silver Steel Mills
17 KM Main Multan Road, Lahore, Pakistan
Phone: +92 324 9500004
Email: info@silversteelmills.com

Request Current Machine Quotation

Frequently Asked Questions

What is the automatic block making machine price in Pakistan?

The price depends on the model, mould, hydraulic system, automation, batching plant, mixer, conveyors, pallet handling and other accessories. SSM 15, 18, 24, 28, 35 and 50 are different production configurations, so the final price should be confirmed through a current itemized quotation.

Which is the best automatic block making machine in Pakistan?

The best machine depends on your product and production target. SSM 15 and SSM 18 can suit smaller or growing businesses, while SSM 24, SSM 28, SSM 35 and SSM 50 are intended for progressively larger automatic production requirements.

Can one machine make both blocks and pavers?

A compatible machine can manufacture different moulded concrete products by changing the appropriate mould and adjusting the machine for the product. Before purchase, confirm that the required mould dimensions and product geometry are compatible with the selected machine.

Can an automatic block machine make 6-inch and 8-inch blocks?

Yes, compatible moulds can be designed for different block sizes. The mould height, cavity arrangement and machine working range must be checked before ordering.

Can the machine produce 60 mm and 80 mm pavers?

Compatible paver moulds can be designed for different thicknesses such as 60 mm and 80 mm. The exact mould and machine setup should be confirmed against the required paver dimensions.

Can the SSM machine produce coloured pavers?

Yes, suitable SSM configurations can be supplied with colour/topping systems for double-layer paving products. The SSM 24 published configuration includes separate concrete and colour mixing/feeding equipment.

Does hydraulic pressure alone determine block strength?

No. Final product strength also depends on cementitious mix design, aggregate quality, moisture, mould filling, vibration, compaction, demoulding and curing. Machine tonnage should therefore not be treated as a guaranteed PSI rating.

Does Silver Steel Mills provide moulds?

Moulds can be specified according to the customer's required product. The buyer should provide exact product dimensions or a drawing so the correct mould configuration can be selected.

Does Silver Steel Mills provide batching and mixer systems?

Yes, automatic SSM production lines can be configured with batching, mixing, conveying and pallet-handling equipment. The exact equipment included depends on the selected machine and quotation.

How much space is required for a block machine plant?

The required space depends on whether you are installing only the block machine or a complete plant with batching, mixer, conveyors, pallets, stacker and curing/stockyard areas. A complete layout should be prepared before construction.

How many workers are required for an automatic block machine?

Automation can significantly reduce manual handling, but the actual labour requirement depends on batching, material loading, machine operation, pallet handling, curing and finished-product loading. A complete manpower plan should be based on the final plant configuration.

Can I buy an automatic block machine in Lahore?

Silver Steel Mills operates from Lahore and manufactures SSM block-making machinery in Pakistan. Customers from other cities can also discuss transportation, installation and commissioning requirements.

Which mould should I buy first?

Choose the mould according to the product you already have demand for. If your market is mainly masonry blocks, start with the required block mould. If your market is paving, select the paver mould and consider whether a double-layer colour/topping system is required.

Final Buying Checklist

✓ Select product first.
✓ Confirm exact product dimensions.
✓ Select mould configuration.
✓ Define daily production target.
✓ Decide semi-automatic or fully automatic.
✓ Confirm hydraulic system.
✓ Confirm vibration system.
✓ Confirm batching plant.
✓ Confirm mixer capacity.
✓ Confirm conveyor system.
✓ Confirm pallet size.
✓ Confirm automatic stacker.
✓ Confirm electrical load.
✓ Prepare factory layout.
✓ Prepare civil foundation.
✓ Confirm installation scope.
✓ Confirm operator training.
✓ Confirm warranty and spare parts.
✓ Confirm transport and taxes.
✓ Obtain a written itemized quotation.

Conclusion

An automatic block making machine is not simply a hydraulic press. A successful concrete-products factory is a complete production system in which mould design, raw materials, batching, mixing, vibration, hydraulic compaction, pallet handling and curing all work together.

Silver Steel Mills' SSM range gives customers different options from the SSM 15 and SSM 18 for smaller/growing businesses through the SSM 24 and SSM 28 for higher-production plants and the SSM 35 and SSM 50 for industrial-scale manufacturing.

The right machine should be selected according to the products you will sell, the moulds you need, your daily production target, factory space, electrical capacity and available investment—not simply because one model has the largest advertised production number.

For the latest automatic block making machine price in Pakistan, send Silver Steel Mills your required product, dimensions and production target for a current machine and mould quotation.

Technical specifications, production figures and prices may vary according to machine configuration, mould, product dimensions, raw materials, cycle settings, electrical arrangement and project scope. Confirm the final specification in the official quotation before placing an order.

SSM 35 Fully Automatic Hydraulic Block Making Machine

Real Proof – The Strength Test

In a recent factory test, Silver Steel Mills engineers ran a batch of zigzag interlocking pavers using the SSM 35. The pavers were freshly pressed — still wet, not cured, not dried.

A 90‑kg worker was asked to stand on a single paver. Then he jumped. Then he stood on one leg.

The result: No crack. No deformation. No chipping at the edges.

“Even though the bricks were wet and full of water, they supported the worker’s full weight without any damage. The compaction density is extremely high — that’s the power of 300‑ton hydraulic pressure.” — Silver Steel Mills Engineer

SSM 35 – Technical Specifications

Parameter	SSM 35 (Fully Automatic)
Operation	Full automatic with PLC control box
Hydraulic Pressure	300 tons (30 HP pump)
Vibration Motors	2 units × 20 HP (total 40 HP)
Mould Cycle Time	20–30 seconds
Daily Production (Solid Blocks)	10,000–12,000 bricks
Daily Production (Pavers/Tiles)	35,000–50,000 tiles
Total Connected Load	131 HP (including conveyors, mixer, stacker)
Control System	Digital PLC with touch screen
Mould Change Time	Less than 20 minutes

Who Should Buy the SSM 35?

♻️

Fly Ash Brick Manufacturers

Turn waste fly ash into profit — free raw material from power plants

🏗️

Paver / Tuff Tile Producers

Supply DHA, Bahria Town, Gulberg Greens, and CPEC housing projects

📋

Government Tender Contractors

NHA, C&W, and Punjab government projects now mandate machine-made blocks

🏢

Real Estate Developers

Captive plants save 40-50% compared to buying from outside

Real Projects – Case Studies

1. CSCEC CPEC Motorway (2018-2019)

Client: China State Construction Engineering Corporation (CSCEC)

Project: Multan-Sukkur Motorway

Challenge: Critical shortage of solid blocks and curb stones — local suppliers could not meet daily demand

Solution: Five SSM 18 plants installed at Kotri, Ghotki, and Jalalpur Pirwala

✅ 8,000 solid blocks/day per plant | 2,000 curbstones/day per plant | Motorway completed months ahead of schedule

“CSCEC officials publicly acknowledged that Silver Steel Mills’ local machinery outperformed Chinese equipment in terms of reliability and production consistency.”

2. Nishat Power, Lahore

Client: Nishat Power Limited

Challenge: 35 tons of fly ash daily — a serious environmental liability

Solution: SSM 15 installed to convert fly ash into bricks

✅ 10,000 fly ash bricks/day | Waste converted to revenue | Running without major breakdown since 2017

“We never imagined that our waste fly ash could become a profitable product. Silver Steel Mills made it possible.” — Plant Manager, Nishat Power

SSM Automatic Machine Lineup – Models Overview

⭐

SSM 24

SSM 35

Industrial Flagship

Fully Automatic — Digital batching + stacker

📐 Daily Tiles: 35,000+
🧱 Daily Blocks: 10,000-12,000
⚡ Hydraulic: 300 tons
💰 Price: PKR 1.5 Crore
🏗️ Space: 1,500-2,000 sqft

Get Quote →

🏭

SSM 50

Mega Plant

Fully Automatic — Industrial mega-plant

📐 Daily Tiles: 50,000+
🧱 Daily Blocks: 15,000+
⚡ Hydraulic: 350+ tons
💰 Price: PKR 1.8 Crore+
🏗️ Space: 2,000-2,500 sqft

Get Quote →

2026 Automatic Block Machine Price Guide

Model	Type	Daily Output (Tiles)	Price Range (PKR)	Best For
SSM 24	Fully Automatic	24,000+	75-85 Lakh	Most popular, balanced production
SSM 35	Fully Automatic	35,000+	1.4-1.6 Crore	Industrial flagship, CPEC projects
SSM 50	Fully Automatic	50,000+	1.8-2.2 Crore	Mega projects, government tenders

* Prices are estimates as of August 2026 and vary by configuration, customization, and steel market conditions. Contact us for an accurate quotation.

What’s Included in the Price?

⚙️

Main Block Machine

Hydraulic power pack, vibration motors, PLC control

🔄

Batching System

Digital batching with load cells for precision

🧱

Moulds & Accessories

1 set of moulds as per requirement, conveyor, stacker

SSM 35 vs Imported Machines

Feature	Imported Chinese QT4-20	Silver Steel Mills SSM 35
After-Sales Support	Very limited, language barrier	24/7 local support, parts available
Hydraulic Pressure	180-200 tons	300 tons (50% stronger)
Steel Thickness	15-20 mm base	30-50 mm base
PLC System	Standard, no Urdu	Customised with Urdu/English
Delivery Time	60-90 days	30-45 days
Price	High + customs duty	Competitive, no hidden charges

Why Silver Steel Mills Automatic Machines Stand Out

🔧

Heavy-Duty Construction

Ultra-thick mould frames, 3mm welding, reinforced hydraulic components — built to last decades

📋

Localized for Pakistan

Higher hydraulic pressure, thicker steel plates, Urdu PLC software, and readily available spare parts

🎓

Training & Support

On-site commissioning, operator training, and 24/7 after-sales support

Frequently Asked Questions

What is the price of an automatic block making machine in Pakistan?

Prices range from PKR 75-85 Lakh for the SSM 24 (24,000+ tiles/day) to PKR 1.8-2.2 Crore for the SSM 50 (50,000+ tiles/day). Contact us for a custom quote based on your specific requirements.

What is the difference between SSM 24, SSM 35, and SSM 50?

SSM 24 is the most popular model with 24,000+ tiles/day and 200-ton hydraulic pressure. SSM 35 is the industrial flagship with 35,000+ tiles/day and 300-ton pressure. SSM 50 is the mega plant with 50,000+ tiles/day and 350+ ton pressure.

How many workers are needed to run the SSM 35?

Only 3-4 workers — one operator, one loader, one helper, one stacker. Fully automatic machines significantly reduce labor costs.

Can I produce different products on the same machine?

Yes. By changing the mould, you can produce solid blocks, hollow blocks, pavers, curbstones, and fly ash bricks. Mould change takes less than 20 minutes.

What is the minimum space required for an SSM 35 plant?

For the complete plant (including batching and stacking), you need 7,000-10,000 sq. ft. (approximately 2 kanals).

Does Silver Steel Mills provide installation and training?

Yes. Our engineers will visit your site, erect the machine, commission it, and train your operators for 1-2 weeks. All at no extra cost (buyer provides local hospitality).

What warranty does SSM offer?

12 months on the main structure and hydraulic system. Motors carry 6-month warranty. Spare parts are available at market price from our Lahore facility.

How can I get an automatic block machine quotation?

Contact our team with your requirements — model preference, daily production target, and budget. We’ll provide a detailed itemized quotation within 24-48 hours.

SSM Automatic Block Machine Models

Silver Steel Mills currently presents several SSM machine configurations.
The following matrix is intended to help buyers understand the model
range. Final specifications, output and quotation should be confirmed
by SSM for the required mould and production product.

Model	Automation	Typical Position in Product Range	Suitable Application	Price / Quote
SSM 15	Semi-automatic configuration	Entry / smaller production requirement	Small and growing block or paver businesses	Current quotation required
SSM 18	Semi-automatic configuration	Growing production	Block, paver and specialised material applications	Current quotation required
SSM 24	Fully automatic / PLC configuration	Medium to large production	Commercial block and paver production	Current quotation required
SSM 35	Fully automatic industrial configuration	High-output production	Industrial block, brick and paver plants	Current quotation required
SSM 50	Fully automatic industrial configuration	Mega / high-volume production	Large industrial and infrastructure-oriented plants	Current quotation required

Model availability, configuration, production capacity and price can
vary according to mould, product dimensions, automation scope and
project requirements. Ask SSM for the current technical quotation.

What Determines the Price of an Automatic Block Making Machine?

Two machines that look similar in photographs can have substantially
different prices because their production systems and included equipment
are different.

1. Automation Level

Manual, semi-automatic and fully automatic plants require
different control systems and levels of material handling.

2. Required Production

Your target output determines the appropriate machine size,
mould arrangement and supporting equipment.

3. Product & Mould

Hollow blocks, solid blocks, pavers, kerbstones and other
products require different mould configurations.

4. Batching & Mixing

A complete automated production line may include aggregate
batching, weighing, mixing and material-transfer equipment.

5. Handling Equipment

Conveyors, pallet systems, stackers and other automation
equipment can increase the overall plant cost.

6. Site & Electrical Requirements

Installation location, available electrical supply, factory
layout and supporting civil work should be considered before
selecting the final machine configuration.

Why There Is No Single Automatic Block Machine Price

A common mistake when researching block machine prices in Pakistan is
comparing the price of the main machine with the price of a complete
production plant.

A quotation may include only the block machine and mould, while another
quotation may include a complete system with batching, mixer, conveyor,
pallets and automated product handling.

For a useful price comparison, ask every manufacturer to state:

Machine model and automation level
Mould type and product dimensions
Included hydraulic system
Control panel / PLC scope
Mixer and batching scope
Conveyor and handling equipment
Number and type of moulds
Installation and commissioning scope
Transport and taxes
Warranty and after-sales terms

What Can an Automatic Block Machine Produce?

The actual products depend on the selected mould, machine configuration
and concrete mix. A suitable production system can be configured for
different mould-based concrete products.

Concrete hollow blocks
Solid concrete blocks
Interlocking pavers
Tuff tiles / paving products
Kerbstones
Other compatible moulded concrete products

Before ordering, provide the exact product drawing or dimensions.
This allows the manufacturer to select the appropriate mould and
production configuration.

Automatic vs Semi-Automatic Block Making Machine

Factor	Semi-Automatic	Fully Automatic
Initial investment	Generally lower	Generally higher
Manual intervention	Higher	Lower
Production scale	Suitable for smaller / growing operations	Suitable for larger production requirements
Material handling	Depends on configuration	Can be integrated with automated batching and conveying
Best buying decision	When investment and flexibility are priorities	When consistent high-volume production is required

Which Automatic Block Machine Is Right for Your Business?

Starting a New Block Business?

Focus first on your local market, product demand, available
capital, factory space and expected daily sales rather than
choosing the largest machine.

Already Selling Blocks?

Compare your current daily sales with the required production
target and determine whether automation will solve your actual
bottleneck.

Housing Scheme or Contractor?

A higher-output production line may be appropriate where large
quantities of blocks or pavers are required within a defined
construction schedule.

Large Industrial Project?

Request a complete plant proposal covering machine, batching,
mixing, conveying, handling, electrical requirements and
installation scope.

Information Needed for an Accurate Machine Quotation

Instead of asking only “automatic block machine price in Pakistan?”,
send the following information to the manufacturer. It makes the
quotation much more useful.

Product type: block, paver, brick or kerbstone
Product dimensions and mould drawing
Target production per day or shift
Required automation level
Factory location
Available factory space
Electrical supply available at site
Required number of moulds
Whether batching and mixer are required
Whether conveyor and stacking are required

How to Buy an Automatic Block Making Machine from Silver Steel Mills

STEP 01

Share Requirements

Tell us what product you want to manufacture and your target output.

STEP 02

Technical Review

The machine configuration and mould requirements are reviewed
against your production target.

STEP 03

Quotation

Receive a quotation showing the selected machine configuration
and included equipment.

STEP 04

Manufacturing & Delivery

After order confirmation, the agreed manufacturing, testing,
delivery and installation scope is followed.

Why Buy a Locally Manufactured Block Machine?

For Pakistani buyers, the purchase decision is not only about the
machine’s initial cost. Availability of technical support, replacement
components, moulds, maintenance knowledge and communication with the
manufacturer can also matter over the operating life of the plant.

Direct Manufacturer Communication

Discuss your actual product and production requirements directly
with Silver Steel Mills rather than selecting a generic machine
from a catalogue.

Custom Mould Requirements

Different concrete products require different moulds. Confirm
your product dimensions before finalizing the machine.

Complete Plant Planning

Where required, the machine can be considered together with
batching, mixing, conveying and handling equipment.

Explore Related Block Machine Solutions

Block Machine in Pakistan

Explore Silver Steel Mills’ broader block-machine range and
production solutions.

View Block Machine Range →

Block Machine for Sale

Review machine configurations designed for commercial
block and paver production.

View Machines for Sale →

Block Machine Manufacturing

Learn more about Silver Steel Mills’ block-machine manufacturing
and equipment range.

Meet the Manufacturer →

Frequently Asked Questions About Automatic Block Machines

What is the price of an automatic block making machine in Pakistan?

There is no single price for every automatic block machine.
The quotation depends on the model, automation level, mould,
required production, batching and mixing equipment, conveyors,
stacking system and other project requirements. Contact Silver
Steel Mills for the current configuration and quotation.

Which SSM machines are fully automatic?

Silver Steel Mills presents the SSM 24, SSM 35 and SSM 50 as
fully automatic configurations in its current machine information.
The exact equipment package should be confirmed in the quotation.

Can one block machine make different products?

Yes, compatible products can generally be produced by changing
the mould configuration. The exact product range should be confirmed
against the selected machine and mould.

What information should I send to get a block machine quotation?

Send the product type, product dimensions, mould requirements,
desired production per day or shift, factory location, available
space, electrical supply and whether you need batching, mixer,
conveyor or stacking equipment.

Is a fully automatic machine better than a semi-automatic machine?

Not necessarily for every buyer. A fully automatic plant is more
suitable when the business requires higher production and reduced
manual handling. A semi-automatic machine may be more appropriate
when investment level and operational simplicity are more important.

Does Silver Steel Mills manufacture block machines in Pakistan?

Silver Steel Mills operates as a Pakistani manufacturer of
construction machinery and publishes SSM block-machine
configurations for the local market. Contact the company directly
to confirm the current manufacturing and delivery scope for your
required model.

That machine exists. It is the SSM 35 – the fully automatic hydraulic block making machine from Silver Steel Mills, Pakistan’s most trusted name in construction machinery.

This article takes you inside the world of high‑compression, zero‑defect block production. You will see why the SSM 35 outperforms ordinary mechanical machines, how its robust design guarantees decades of trouble‑free operation, and why top Pakistani developers – including Nishat Power, CSCEC (CPEC motorway), DHA Multan, and Gulberg Greens – rely on Silver Steel Mills.

Whether you are a contractor, a real estate developer, or an aspiring entrepreneur, this guide will show you how the SSM 35 can give you free raw material (fly ash), government subsidies, and monthly profits up to PKR 1.5 million.

Why Choose a Fully Automatic Hydraulic Block Machine?

Most small‑scale block makers use mechanical or semi‑automatic machines that rely on simple vibration. These machines produce weak, irregular blocks that crumble under pressure.

The SSM 35 is different. It combines three powerful forces:

Force	Function
Hydraulic pressure (up to 300 tons)	Compacts the raw material into a dense, rock‑hard mass
High‑frequency vibration (2 × 20 HP motors)	Eliminates air voids and ensures uniform density
Precise mould geometry	Produces perfect edges and sharp faces every cycle

The result? Bricks that are so strong that a 90‑kg worker can jump on them while they are still wet, without any crack or damage. You will see proof in this article.

Real‑Life Demonstration: Strength Test on Wet Zigzag Pavers

In a recent factory test, Silver Steel Mills engineers ran a batch of zigzag interlocking pavers using the SSM 35. The pavers were freshly pressed – still wet, not cured, not dried.

A 90‑kg worker was asked to stand on a single paver. Then he jumped. Then he stood on one leg. The result:

No crack
No deformation
No chipping at the edges

“Even though the bricks were wet and full of water, they supported the worker’s full weight without any damage. The compaction density is extremely high – that’s the power of 300‑ton hydraulic pressure.” – Silver Steel Mills Engineer

This is not just a demonstration; it is a guarantee of quality. When you buy an SSM 35, every block you produce will be strong enough for road pavements, industrial floors, and CPEC‑grade construction.

The SSM 35 – Technical Specifications (Localised from QT4‑20)

Parameter	SSM 35 (Fully Automatic)
Operation	Full automatic with PLC control box
Hydraulic pressure	300 tons (from 30 HP pump)
Vibration motors	2 units × 20 HP (total 40 HP)
Mould cycle time	20–30 seconds
Daily production (solid blocks)	10,000–12,000 bricks
Daily production (pavers/tiles)	24,000–50,000 tiles
Total connected load	131 HP (including conveyors, mixer, stacker)
Control system	Digital PLC with touch screen (recipe storage, auto cycle)
Mould change time	< 20 minutes
Pallet size	889 × 1219 × 38 mm (wooden)

Built to Last – No Maintenance Headaches

One of the biggest fears of buying a block machine is frequent breakdowns – worn‑out moulds, cracked hydraulic jacks, broken welds, and expensive spare parts.

The SSM 35 is engineered to eliminate those fears.

1. Ultra‑Thick Mould Frames

The mould body (die) is made from imported heat‑treated steel, much thicker than ordinary machines. You can literally use your finger to measure the wall thickness – it is that substantial. This means:

No bending or warping after thousands of cycles
No dimensional errors even after years of use
Perfect sharp edges on every brick

2. Reinforced Welding

Every weld on the SSM 35 is 3‑mm thick – far more than the usual 1‑mm weld found on cheap machines. Look closely at the frame joints. You will see smooth, even, beautiful welding lines that distribute stress uniformly. No weak points. No cracks.

3. Heavy‑Duty Hydraulic Components

The hydraulic jack (cylinder) and pressure pipes are imported from Taiwan/China with 3‑ply high‑pressure hoses. The seals are grade‑A, designed for 16‑hour continuous operation in Pakistan’s 50°C summer heat.

4. Anti‑Rust Painting

Before final painting, every steel part receives anti‑rust primer. The top coat is industrial‑grade epoxy paint. This is why the machine keeps its appearance and structural integrity for over a decade, even in humid coastal areas like Karachi.

5. Tension Spring System (For Material Cart)

The material cart (which carries wet concrete to the mould) moves along a heavy channel. Without proper design, the channel wears out quickly. Our SSM 35 uses four tension springs to reduce friction and distribute load. The result: the channel lasts for millions of cycles without deformation.

50+ Years of Proven Technology – With a Pakistani Advantage

The basic design of the SSM 35 has been in the global market for over 50 years. Thousands of machines are running in more than 50 countries. Silver Steel Mills has taken this mature, time‑tested technology and localised it for Pakistani conditions:

Higher hydraulic pressure (300 tons vs 180 tons on standard machines)
Thicker steel plates (30‑50 mm base, compared to 15‑20 mm on imports)
Local PLC software in English/Urdu for easy operation
Readily available spare parts from our Gujranwala factory

“Our clients report more than 95% satisfaction. Many have bought second and third machines without ever needing a major repair. The SSM 35 runs for years with zero maintenance – just oil changes and periodic bolt tightening.” – Silver Steel Mills Service Head

Who Should Buy the SSM 35? (Target Market for Pakistan)

1. Fly Ash Brick Manufacturers (Free Raw Material)

Thermal power plants in Pakistan produce thousands of tons of fly ash daily. This waste is given away free of charge. Use the SSM 35 to produce lightweight, high‑strength fly ash bricks at a cost of just PKR 6‑8 per brick and sell them for PKR 12‑15. Your profit per brick = PKR 6‑9.

Daily profit (10,000 bricks) = PKR 60,000 to PKR 90,000.

2. Paver / Tuff Tile Producers for Housing Schemes

DHA, Bahria Town, Gulberg Greens, and CPEC housing projects need millions of interlocking pavers. The SSM 35 produces 24,000 tiles per day – enough to pave 200‑250 square metres every shift.

3. Contractors for Government Tenders

The Punjab government, NHA, and C&W department now mandate the use of machine‑made concrete blocks for all infrastructure projects. With an SSM 35, you can bid for tenders with confidence, knowing you can deliver consistent quality and huge volumes.

4. Real Estate Developers (Captive Plants)

Developers like DHA Multan and Gulberg Greens have installed SSM 35 plants to manufacture their own blocks and pavers – saving 40‑50% compared to buying from outside.

Case Study – CSCEC CPEC Motorway (2018‑2019)

When China State Construction Engineering Corporation (CSCEC) built the Multan‑Sukkur motorway, they faced a critical shortage of solid blocks and curb stones. Local suppliers could not meet the daily demand. They turned to Silver Steel Mills.

We installed five SSM 18 plants (the compact version of SSM 35) at Kotri, Ghotki, and Jalalpur Pirwala. Each plant delivered:

8,000 solid blocks/day
2,000 curbstones/day

The result? The motorway was completed months ahead of schedule. CSCEC officials publicly acknowledged that Silver Steel Mills’ local machinery outperformed Chinese equipment in terms of reliability and production consistency.

Case Study – Nishat Power, Lahore (Fly Ash to Profit)

Nishat Power Limited generated 35 tons of fly ash daily – a serious environmental liability. After installing an SSM 15 (smaller version of SSM 35), they now produce 10,000 fly ash bricks/day. The waste has become a steady revenue stream, and the plant has been running without major breakdown since 2017.

“We never imagined that our waste fly ash could become a profitable product. Silver Steel Mills made it possible.” – Plant Manager, Nishat Power

Price of SSM 35 in Pakistan (2025)

Configuration	Price (PKR)	Remarks
SSM 35 (basic, single mould, no batching)	1.2 – 1.4 crore	Ex‑factory Gujranwala
SSM 35 with complete batching plant, 2 mixers, conveyor, stacker	1.5 – 1.8 crore	Turnkey solution
Additional moulds (pavers, curb stones, hollow blocks)	6 – 8 lakh per set	Custom made
Wooden pallets (1,000 pcs)	55 – 60 lakh	889×1219×38 mm

Prices are subject to GST and delivery charges. For a firm quotation, please contact our sales team.

Why Silver Steel Mills Is Better Than Imported Brands

Feature	Imported Chinese QT4‑20	Silver Steel Mills SSM 35
After‑sales support	Very limited, language barrier	24/7 local support, parts available
Hydraulic pressure	180‑200 tons	300 tons (50% stronger)
Steel thickness	15‑20 mm base	30‑50 mm base
PLC system	Standard, no Urdu	Customised with Urdu/English
Delivery time	60‑90 days	30‑45 days
Price	High + customs duty	Competitive, no hidden charges

Frequently Asked Questions (FAQ)

Q1: How many workers are needed to run the SSM 35?
A: Only 3‑4 workers (one operator, one loader, one helper, one stacker). Fully automatic machines reduce labour cost.

Q2: What is the minimum space required?
A: For the complete plant (including batching and stacking), you need 7,000‑10,000 sq. ft. (approx. 2 kanals).

Q3: Can I produce different products on the same machine?
A: Yes. By changing the mould, you can produce solid blocks, hollow blocks, pavers, curbstones, and fly ash bricks. Mould change takes less than 20 minutes.

Q4: How long does the machine last?
A: With proper maintenance (regular oil changes, cleaning), the SSM 35 easily lasts 20‑30 years. The mould may need replacement after 5‑8 years of heavy use.

Q5: Do you provide installation and training?
A: Yes. Our engineers will visit your site, erect the machine, commission it, and train your operators for 1‑2 weeks. All at no extra cost (buyer provides local hospitality).

Q6: What is the warranty?
A: 12 months on the main structure and hydraulic system. Motors (reconditioned European) carry 6‑month warranty. Spare parts are available at market price.

In this comprehensive guide, we will walk you through the exact process of changing the mould from paver/tile mode to hollow block mode. This procedure is critical when you need to switch production from 60mm thick pavers to 200mm high hollow blocks – a height difference of 140mm.

Whether you are an operator at a CPEC motorway plant, a DHA housing scheme site, or a private block manufacturing unit, this step-by-step manual will ensure you perform the changeover safely, accurately, and efficiently.

Note: This guide is based on the official training provided by Silver Steel Mills’ engineers. Always follow safety protocols and consult your machine’s manual. The procedure described here applies to SSM 35 and other SSM series machines (SSM 24, SSM 18, SSM 50) with similar design.

Why You Need to Change the Mould on SSM 35

Product	Typical Height	Mould Type
Paving tiles / Tuff tiles	50-60 mm	Paver mould (flat, interlocking)
Hollow blocks	200 mm	Hollow block mould (with cavities)
Solid blocks	200 mm	Solid block mould
Curb stones	150-200 mm	Curb stone mould

The difference in height between a paver mould (60mm) and a hollow block mould (200mm) is 140mm. Therefore, you must adjust the machine’s height settings and replace the mould components to accommodate the taller product. The SSM 35 is engineered with a motor box lifting mechanism, adjustable tie rods, and precision locking nuts to make this changeover quick and repeatable.

Tools Required

Before starting, gather the following tools (all provided with your SSM 35 machine):

Spanner / Wrench set (to loosen/tighten nuts)
Screwdriver (flathead, for small screws)
Allen key set
Fork or pry bar (to lift heavy components)
Rubber mallet (for gentle tapping)
Springs, screws, blades (included in mould change kit)
Safety gloves and goggles

Step-by-Step Mould Change Procedure (Paver → Hollow Block)

Step 1 – Identify the Parts to Remove

First, locate the following components on your SSM 35 machine:

Motor box (the upper part housing the vibration motors)
Support bracket (a metal piece that holds the motor box in place)
Fitting brake mould (the current paver mould assembly)
Tie rods and nuts (vertical threaded rods that control mould height)

Step 2 – Lift the Motor Box

To access the mould area, you must raise the motor box.

Locate the support bracket (an L-shaped or flat metal piece).
Insert a pry bar or use the hydraulic lift (if equipped) to gently raise the motor box.
Fix the support bracket underneath the motor box to hold it securely in the raised position. This prevents accidental lowering during the changeover.

Safety tip: Never work under an unsupported motor box. Always use the mechanical lock or bracket.

Step 3 – Remove the Original Paver Mould (Fitting Brake Mode)

Use a wrench to unscrew the four bolts (one on each corner) that secure the current mould.
Remove the mould carefully and set it aside on a clean wooden pallet.
Also remove any side plates or guide rails that are specific to the paver mould.

Step 4 – Understand the Height Difference

Why do we need to adjust height?

Paver mould height: 60 mm
Hollow block mould height: 200 mm
Difference: 140 mm

Therefore, you must lower the mould support plate by 140 mm to accommodate the taller hollow block mould.

Step 5 – Adjust the Tie Rods and Nuts

The SSM 35 machine has vertical tie rods (threaded rods) that connect the upper mould holder to the lower mould base. The height is adjusted by moving the locking nuts.

Locate the locking nuts on each tie rod (usually near the top or bottom).
Use a wrench to loosen the upper nuts.
Slide the tie rod downwards (or move the nut to a lower position) by exactly 140 mm. You can use a measuring tape or a pre-marked scale on the machine frame.
Once the rod is at the new position, tighten the locking nuts firmly.

Repeat this for all four tie rods (one on each corner). Ensure all are adjusted equally to keep the mould level.

Step 6 – Install the Hollow Block Mould

Lift the hollow block mould (it will be heavier and taller than the paver mould).
Carefully lower it onto the mould support plate.
Align the mould with the guide pins and the hydraulic injection plate.
Insert the springs and screws provided with the new mould. These help absorb vibration and keep the mould in place.
Screw down the four corner bolts (hand-tighten first, then use a wrench).

Step 7 – Lower the Motor Box

Remove the support bracket.
Gently lower the motor box until it rests on top of the new mould.
Critical check: The motor box must touch the pallet (or the top of the mould) evenly. If there is any gap, the vibration will not transfer properly, resulting in poorly compacted blocks.
Use a spacer pallet (a flat wooden board) on top of the mould to help distribute pressure evenly.

Step 8 – Fine-Tune Alignment Using Vibration

If you rely only on your eyes to align the mould, it may not be perfectly centered. The SSM 35 has a smart feature: self-aligning vibration.

Switch on the vibration motors for a few seconds (short burst).
The vibration will naturally settle the mould into the correct position – it will “suck” the mould into perfect alignment with the motor box and the pallet.
After vibration, check that the mould is flush and centered.

Step 9 – Adjust the Height Limit Switches

The machine’s PLC control system has height limit sensors that determine the upper and lower positions of the press plate. For hollow blocks (200 mm), you must adjust these settings.

Consult your SSM 35 manual for the exact procedure (usually via the touch screen or control panel).
Set the upper limit to accommodate the taller mould (increase by 140 mm).
Test a single cycle (without raw material) to ensure no mechanical interference.

Step 10 – Tighten All Bolts and Final Check

Double-check all four corner bolts – tighten them firmly.
Ensure all springs and screws are properly seated.
Remove any tools or debris from the machine area.
Perform a manual test cycle (empty mould) to verify smooth operation.
Check that the pallet is fully seated and that the mould box closes without gaps.

Lifting the motor box and fixing a support bracket.
Removing the paver mould (fitting brake mode).
Loosening the tie rod nuts and lowering them by 140 mm.
Installing the taller hollow block mould (200 mm height).
Using vibration to self-align the mould.
Securing all bolts and performing a test cycle.

The entire process takes 15-20 minutes for an experienced operator. Silver Steel Mills provides on-site training to all SSM 35 buyers, ensuring your team masters this changeover quickly.

Key Differences: Paver Mould vs Hollow Block Mould

Feature	Paver Mould	Hollow Block Mould
Product height	50-60 mm	200 mm
Mould weight	Lighter	Heavier (requires more support)
Cavities	Solid or small interlocking shapes	2-3 rectangular hollow cores
Vibration requirement	Medium frequency	High frequency (20 HP dual motors recommended)
Hydraulic pressure	150-200 tons	200-300 tons (use SSM 35’s full capacity)

Common Mistakes to Avoid

Mistake	Consequence	Solution
Not lifting motor box high enough	Mould won’t slide in/out	Use support bracket and raise fully
Uneven tie rod adjustment	Mould tilts, blocks will be wedge-shaped	Measure each corner equally
Forgetting to tighten corner bolts	Mould shifts during production, damage to machine	Use torque wrench or double-check
Skipping self-alignment vibration	Mould off-center, blocks will have uneven thickness	Always run short vibration burst
Not adjusting PLC height limits	Machine tries to over-travel, may damage sensors	Refer to manual or call Silver Steel Mills support

Why Silver Steel Mills’ SSM 35 Makes Mould Change Easy

Feature	Benefit
Heavy-duty lifting mechanism	Smooth motor box raising with mechanical lock
Threaded tie rods with large nuts	Easy height adjustment without special tools
Pre-drilled alignment holes	Mould self-centers via guide pins
Vibration self-alignment feature	Removes guesswork, ensures perfect fit
PLC with recipe memory	Save height settings for each mould type – one-touch recall

Frequently Asked Questions (FAQ)

Q1: How often do I need to change the mould?

A: As often as your production schedule demands. Some operators change moulds daily (morning: pavers, afternoon: hollow blocks). The SSM 35 is designed for frequent changeovers.

Q2: Can one person perform the mould change?

A: Yes, an experienced operator can do it alone. However, for safety, it is recommended to have a helper when handling heavy moulds (over 100 kg).

Q3: Do I need special lubricants for the tie rods?

A: Apply a light coat of grease to the threads periodically to prevent seizing.

Q4: What if the mould does not align perfectly after vibration?

A: Loosen the corner bolts slightly, run vibration again, then re-tighten. If problem persists, contact Silver Steel Mills support.

Q5: How do I store unused moulds?

A: Keep them on a flat wooden pallet, covered with plastic to prevent rust. Apply anti-rust oil before long-term storage.

Conclusion – Master Your SSM 35 for Maximum Profits

The ability to quickly and accurately change moulds on your SSM 35 block making machine unlocks multiple revenue streams. One day you can produce 15,000 tuff tiles for a housing scheme footpath, and the next day switch to 8,000 hollow blocks for a multi-story building. This versatility is why Silver Steel Mills’ machines are trusted by CPEC contractors, DHA developers, and leading industrialists across Pakistan.

“We change moulds on our SSM 35 twice a week – from pavers to hollow blocks and back. The machine is designed so well that we complete the changeover in under 20 minutes. Silver Steel Mills’ training made all the difference.”
– Plant Supervisor, Ghotki CPEC Motorway Project

If you own an SSM 35 (or any SSM series machine) and need further guidance, Silver Steel Mills offers free remote support and paid on-site service. Contact us to schedule a refresher training for your operators.

About Silver Steel Mills

Silver Steel Mills is Pakistan’s leading manufacturer of block making machines, batching plants, paver plants, and steel structures. With over 500 installations nationwide – including CPEC motorway plants, Nishat Power fly ash brick plants, DHA Multan paver plants, and Gulberg Green block factories – we have the experience and engineering excellence to support your success.

Our SSM series machines (SSM 15, 18, 24, 28, 35, 50) are fully automatic, heavy-duty, and designed for Pakistani conditions. We provide complete turnkey solutions: design, manufacturing, installation, operator training, and after-sales support.

1. Understanding Your Production Scale

We categorize our machinery into two primary functional groups: Semi-Automatic for growing SMEs and Fully Automatic for industrial-scale operations.

The Semi-Automatic Lineup (SSM 15 & SSM 18)

These models are perfect for entrepreneurs starting their journey. They offer the perfect balance between manual oversight and automated compression.

SSM 15 (Single Portion): Designed for versatility, this machine utilizes an auto-pallet system with a single-trolley delivery matrix. It is the workhorse for smaller housing schemes.
SSM 18 (Biomass/Fly Ash Focused): Engineered specifically to handle abrasive industrial wastes. It features extra-large storage hoppers and reinforced chrome shafts to handle the density of biomass and fly ash recipes.

The Fully Automatic Lineup (SSM 24, SSM 35, & SSM 50)

These machines feature our Digital Batching Operating System. They are “multi-functional,” meaning you can produce blocks, hollow units, curbstone, or pavers simply by switching the CNC-engraved die mould.

SSM 24: Our double-layer plant that allows you to apply a premium pigment-rich top surface to your pavers.
SSM 35 & SSM 50: These are our industrial flagships. They incorporate a full-scale automated ecosystem: Aggregate Batching Hopper → Twin Shaft Mixer → Automatic Conveyor System → High-Pressure Hydraulic Press → Automated Product Stacker.

2. Technical Specifications: Why SSM Machines Are Superior

Our machines aren’t just heavy iron; they are calculated, precision-engineered assets. Here is what sets them apart:

The Hydraulic & Vibration Advantage

Every SSM fully automatic plant uses a dual-vibration system combined with high-pressure hydraulic pumping (capable of up to 10,000 PSI). This combination ensures that the air pockets inside the concrete are completely removed, resulting in a product that consistently hits 7,000+ PSI compressive strength. This is why products manufactured on SSM plants are routinely approved for Government and FWO-led projects.

The Integrated Batching System

In the SSM 35 and SSM 50 models, the Digital Batching System eliminates human error. It weighs sand, crush, and cement with electronic precision. When the mix is perfectly calculated, the resulting block is consistent in quality, density, and strength—every single time.

3. Machinery Model Pricing and Capacity Matrix

Model	Classification	Daily Capacity (8-hr shift)	Key Feature
SSM 15	Semi-Auto	~8,000 Bricks	Auto-Pallet delivery
SSM 18	Semi-Auto	~12,000 Bricks	Fly Ash/Biomass specialized
SSM 24	Fully Auto	~18,000 Bricks	Double-Layer pigment ready
SSM 35	Fully Auto	~24,000 Bricks	Digital Batching & Stacker
SSM 50	Fully Auto	~40,000 Bricks	Industrial Mega-Plant

(Note: Prices fluctuate based on steel market rates and hydraulic specification requirements. Please contact our sales desk at 0324-9500004 for a live itemized quotation.)

4. Why Multi-Functional Design Matters

When you invest in an SSM plant, you are investing in a product-agnostic system. One machine can produce:

Hollow Blocks: 12×12, 12×14, and 12×18 inch custom sizes.
Solid Blocks: For load-bearing foundation walls.
Interlocking Pavers: Zig-zag, rectangular, or cosmic shapes for parking zones.
Curbstones: Essential for high-traffic road medians.

By switching the Die Mould, you adapt to the market demand of the day without needing to buy a new production line. This is the definition of a smart, sustainable business.

5. The “Silver Steel” Commitment

We aren’t just selling a machine; we are selling a production solution. When you choose Silver Steel Mills:

On-Site Commissioning: Our engineers arrive at your site in Lahore, Gujranwala, Karachi, or any city in Pakistan to ensure the plant is perfectly aligned.
Operator Training: We train your team until they can manage the digital batching and PLC controls independently.
Local Spare Parts: You will never be dependent on international imports for rubber seals, mould steel, or conveyor parts. We build them here.

Start Your Production Today

Are you ready to stop buying bricks and start manufacturing them? Whether you are aiming for a high-output SSM 50 for a government highway project or an SSM 15 for your regional development, we are ready to assist you.

Factor	Manual / Semi-Auto	Fully Automatic
Labor required	5-7 workers	2-3 operators
Production consistency	Variable	Uniform
Quality control	Insani ghalti ka chance	Machine controlled
Daily output	Limited	High (up to 50,000+ tiles)
Strength achievable	3000-5000 PSI	7000 PSI (govt approved)

Silver Steel Mills Pakistan mein automatic block making machines ka pioneer hai. Hum 3 types ki automatic machines banate hain:

Semi-Automatic – SSM 15, SSM 18
Fully Automatic – SSM 24, SSM 35, SSM 50

Aur sabse important baat – teeno fully automatic models (SSM 24, 35, 50) complete batching system, mixer, conveyor, aur block stacker ke saath aati hain – jisse 7000 PSI tak ki strength wale blocks bante hain jo government projects mein approved hote hain.

Semi-Automatic Block Making Machines (SSM 15, SSM 18)

Semi-automatic machine mein operator ko kuch kaam manual karna padta hai – jaise material daalna, button dabana. Lekin production automatic hoti hai. Ye unke liye best hai jo:

Budget limited ho (45-50 lakh)
Daily 15,000-18,000 tiles kafi ho
Fully automatic ki zaroorat na ho

SSM 15 – Semi-Automatic Entry Level

Specification	Detail
Type	Semi-automatic
Daily Production (Tiles)	15,000+
Daily Blocks (8″ hollow)	4,000-5,000
Hydraulic Pressure	120 tons
Vibration System	High frequency (4500 rpm)
Control	Digital controller (buttons)
Power Requirement	25-30 kW
Space Required	600-800 sqft
Price	Rs 45 Lakh

Included:

Main block machine
Hydraulic power pack
Vibration motors
Digital control panel
1 set molds (as per requirement)
Pan mixer (500 kg)

SSM 18 – Semi-Automatic Higher Production

Specification	Detail
Type	Semi-automatic
Daily Production (Tiles)	18,000+
Daily Blocks (8″ hollow)	5,000-6,000
Hydraulic Pressure	150 tons
Vibration System	High frequency (4800 rpm)
Control	Digital controller + touch screen option
Power Requirement	30-35 kW
Space Required	800-1,000 sqft
Price	Rs 48 Lakh

Included:

Main block machine
Hydraulic power pack
Vibration motors
Digital control panel
1 set molds
Pan mixer (750 kg)

Fully Automatic Block Making Machines (SSM 24, SSM 35, SSM 50)

Yeh machines poori tarah se automatic hain. Aap recipe set karo, raw material daalo, phir machine:

Khud weigh karegi (batching system)
Khud mix karegi (mixer)
Khud convey karegi (conveyor belt)
Khud block banayegi (main machine)
Khud stack karegi (block stacker)

In teeno models mein batching system, mixer, conveyor belt, aur block stacker standard included hai.

SSM 24 – Fully Automatic (Most Popular)

Specification	Detail
Type	Fully Automatic
Daily Production (Tiles)	24,000+
Daily Blocks (8″ hollow)	7,000-8,000
Hydraulic Pressure	200 tons
Vibration System	High frequency (5000 rpm) with servo motor
Control	PLC with 7″ touch screen
Batching System	Automatic (3 bins – sand, crush, cement)
Mixer	Planetary mixer (1000 kg)
Conveyor Belt	8m long, 800mm width
Block Stacker	Automatic (pallet stacker)
Power Requirement	45-50 kW
Space Required	1,200-1,500 sqft
Price	Rs 85 Lakh

Special Features:

Recipe memory (M15, M20, M30 – save karo)
Real-time production monitoring
Moisture correction system
Data logging (kitna block bana, kab bana)

Kis ke liye best hai?

Sab se zyada bikta hai
Perfect balance of price and production
Daily 2-3 trucks ka product
Government projects ke liye approved

SSM 35 – Heavy Duty Fully Automatic

Specification	Detail
Type	Fully Automatic (Industrial Grade)
Daily Production (Tiles)	35,000+
Daily Blocks (8″ hollow)	10,000-12,000
Hydraulic Pressure	300 tons
Vibration System	Dual motor high frequency (5200 rpm)
Control	PLC with 10″ touch screen + remote access
Batching System	Automatic (4 bins – sand, crush, crush, cement)
Mixer	Planetary mixer (1500 kg)
Conveyor Belt	12m long, 1000mm width with scraper
Block Stacker	Automatic with pallet dispenser
Power Requirement	70-80 kW
Space Required	1,500-2,000 sqft
Price	Rs 1.5 Crore (150 Lakh)

Special Features:

Heavy duty structure (Q345B steel)
Dual vibration motors – extra strong blocks
Remote diagnostic support (hum online help kar sakte hain)
Production report print
Compatibility with transit mixer

Kis ke liye best hai?

Industrial scale production
Daily 4-5 trucks
Export quality blocks
Mega projects (dams, highways, airports)

SSM 50 – Mega Scale Fully Automatic

Specification	Detail
Type	Fully Automatic (Mega Industrial)
Daily Production (Tiles)	50,000+
Daily Blocks (8″ hollow)	15,000+
Hydraulic Pressure	400 tons
Vibration System	Servo hydraulic + high frequency (5500 rpm)
Control	PLC with 15″ touch screen + remote + mobile app
Batching System	Automatic (5 bins – multiple aggregates)
Mixer	Planetary mixer (2000 kg)
Conveyor Belt	15m long, 1200mm width with covers
Block Stacker	Full automatic with pallet stacker and destacker
Power Requirement	100-120 kW
Space Required	2,000-2,500 sqft
Price	Rs 1.8 Crore (180 Lakh)

Special Features:

Maximum production – 50,000+ tiles/day
Fully automated – sirf raw material dalo, ready blocks nikalte raho
Mobile app se monitoring (production status, alerts)
7000 PSI blocks consistent
Government tenders mein first choice

Kis ke liye best hai?

Mega scale operation
Daily 7-8 trucks
Ready mix concrete plant ke saath
Export to Afghanistan, Middle East

Comparison Table – All Automatic Models

Model	Type	Daily Tiles	Daily Blocks	Hydraulic	Control	Price (PKR)
SSM 15	Semi-Auto	15,000	4,000-5,000	120 ton	Digital	45 Lakh
SSM 18	Semi-Auto	18,000	5,000-6,000	150 ton	Digital+	48 Lakh
SSM 24	Fully Auto	24,000	7,000-8,000	200 ton	PLC 7″	85 Lakh
SSM 35	Fully Auto	35,000	10,000-12,000	300 ton	PLC 10″	1.5 Crore
SSM 50	Fully Auto	50,000	15,000+	400 ton	PLC 15″+app	1.8 Crore

Batching System – Quality Concrete Ka Secret

Fully automatic models (SSM 24, 35, 50) mein batching system standard included hai. Batching system woh hai jo material ko exact weight karta hai.

Batching System Components:

Component	Function
Aggregate bins (3-5 bins)	Sand, crush, different sizes
Load cells	Exact weight measurement (±0.5% accuracy)
Cement silo connection	Cement weight control
Water weighing tank	Exact water quantity
PLC controller	Automatic weighing sequence

Batching System Kyun Zaroori Hai?

Without Batching (Manual)	With Automatic Batching
Andaza se material mix	Exact weight se mix
Quality inconsistent	Quality consistent (7000 PSI)
Blocks weak (2000-3000 PSI)	Blocks strong (5000-7000 PSI)
Government project reject	Government project approved
Wastage zyada	Wastage kam

Government projects mein batching system wali machine mandatory hoti hai. Aapke blocks random test honge – agar consistent quality nahi to blacklist ho sakte ho.

Mixer Machine – Kya Type Hai?

Fully automatic models mein planetary mixer aata hai. Normal pan mixer se bohat behtar hai.

Planetary Mixer vs Pan Mixer:

Feature	Pan Mixer	Planetary Mixer (SSM 24/35/50)
Mixing action	Blade rotates only	Blade + pan both rotate
Mixing time	60-90 seconds	30-45 seconds
Uniformity	Good	Excellent
Wear parts life	6-12 months	12-24 months
Best for	Small scale, manual	Automatic, industrial

Planetary Mixer Specifications (SSM 35/50):

Parameter	SSM 35	SSM 50
Capacity (per batch)	1500 kg	2000 kg
Motor power	45 kW	55 kW
Mixing time	30-40 seconds	30-40 seconds
Discharge	Automatic hydraulic	Automatic hydraulic
Lining	Wear-resistant steel	Wear-resistant steel

Conveyor Belt – Material Transfer

Mixer se block machine tak material transfer karne ke liye conveyor belt hoti hai.

Parameter	SSM 24	SSM 35	SSM 50
Length	8 meters	12 meters	15 meters
Width	800 mm	1000 mm	1200 mm
Motor	5.5 kW gear motor	7.5 kW	11 kW
Belt type	Rubber with cleats	Rubber with cleats	Heavy duty with sidewalls
Speed	Adjustable	Adjustable	Adjustable

Conveyor belt automatic hai – machine chali to belt chali. Manual intervention nahi.

Hydraulic Vibration System – Strong Blocks Ka Rahas

Block machine mein do cheezein blocks ko strong banati hain:

Hydraulic pressure – material ko compress karta hai
Vibration – material ko settle karta hai, air bubbles nikalta hai

SSM Series Hydraulic & Vibration Specs:

Model	Hydraulic Pressure	Vibration Type	Vibration Frequency
SSM 15	120 tons	Electric vibrator	4500 rpm
SSM 18	150 tons	Electric vibrator	4800 rpm
SSM 24	200 tons	Servo hydraulic + vibrator	5000 rpm
SSM 35	300 tons	Dual vibrator	5200 rpm
SSM 50	400 tons	Servo hydraulic + dual	5500 rpm

Hydraulic + vibration combination se blocks dense aur strong bante hain – 7000 PSI tak.

7000 PSI Strength – Kya Matlab Hai Aur Kaise Achieve Hoti Hai?

PSI = Pounds per Square Inch – yeh block ki compressive strength hai.

PSI Level	Quality	Use
2000-3000 PSI	Low	Footpaths, garden (light traffic)
3000-4000 PSI	Medium	Driveways, parking
4000-5000 PSI	Good	Commercial areas
5000-6000 PSI	Very good	Industrial areas, roads
6000-7000 PSI	Excellent	Heavy traffic, main roads, airports, government projects

7000 PSI Kaise Achieve Karte Hain?

Factor	Role
Exact batching	Automatic weighing system
High quality cement	OPC 53 grade
Proper mixing	Planetary mixer, proper time
High hydraulic pressure	200-400 tons
High frequency vibration	5000-5500 rpm
Proper curing	21-28 days
Good aggregate	Clean crush, proper gradation

Silver Steel Mills ki fully automatic machines (SSM 24/35/50) yeh sab provide karti hain – isliye 7000 PSI possible hai aur government projects approved hain.

Parameter	Specification
Model	SSM 35 (Fully Automatic)
Cycle Time	15‑20 seconds
Hydraulic Pressure	300 tons
Vibration	Dual 20 HP motors (under‑bed + shaft)
Total Power	45‑50 kW (25 kW meter sufficient)
Pallet Size	889 × 1219 × 38 mm
Daily Output	Up to 18,000 pavers or 12,000 hollow blocks
Special Feature	Integrated color material feeding system for multi‑layer pavers

Key Design Improvements Over Previous Models

1. Unified Material Cutting Channel (Single vs. Double)

Older design: Used two channels (upper and lower) to guide the concrete material cut, causing excessive wear and misalignment.

SSM 35 innovation: A single, reinforced channel now supports the material cutting carriage. This simplification reduces friction points, increases rigidity, and ensures smoother forward/back movement of the concrete feed box.

✅ Less wear on bearings and channels
✅ More stable material feeding
✅ Longer service life of the cutting carriage

2. Advanced Spring‑Loaded Vibration Dampening

Wear between the material cutting channel and the bearings is a common failure point in block machines. The SSM 35 integrates eight heavy‑duty springs (positions: front, rear, sides, and interior) that actively absorb vibration and reduce metal‑to‑metal contact.

Spring Location	Quantity	Function
Front side visible	2	Absorb forward impact
Rear side	2	Absorb backward impact
Left interior	2	Reduce lateral wear
Right interior	2	Balance channel movement
Total	8	Maximum dampening

Result: Bearings and channels last 30‑40% longer, reducing downtime and replacement costs.

3. Heat‑Treated Bearings and Channels

All critical wear parts – including the linear bearings and the steel channel – are heat‑treated to achieve higher hardness and strength than normal steel.

Brinell hardness increased by 25%
Wear resistance improved by 40%
Suitable for continuous 16‑hour shifts in Pakistan’s hot climate (45‑50°C)

4. Extended Channel for Mold Protection

In previous versions, the material cutting channel ended before the mold area. When the carriage moved forward, it would drop the concrete mix directly onto the mold surface, causing accelerated mold wear and uneven filling.

SSM 35 solution: The channel is now extended all the way to the end of the mold area. This means:

The concrete carriage remains supported until it fully clears the mold.
No direct impact of the carriage on the mold edges.
Mold life increases by up to 50%.
Better concrete distribution = higher block strength uniformity.

5. Color Material Feeding System – The Biggest Upgrade

The SSM 35 features a dedicated, fully automatic color feeding system that allows you to produce two‑layer pavers (a strong grey concrete base + a thin colorful top layer) without manual intervention.

How It Works:

Base concrete (grey) is fed via the main hopper.
Color pigment mix (e.g., red, yellow, green) is loaded into a separate small hopper.
The color carriage moves forward, spreads the colored material evenly over the mold surface.
Then it retracts, and the main carriage feeds the base concrete.
The hydraulic press and vibration units compact both layers into a single, solid paver with a beautifully colored top surface.

Key Advantages of the New Color System:

Feature	Benefit
Same‑level channel connection	Color carriage runs on the same channel as the main carriage – no extra alignment needed.
Spring‑loaded carriage	Reduces wear on the color feeding box and mold.
Clean retraction	Springs help scrape off excess color material, preventing waste and color contamination.
Up to 95% pigment savings	The system clears almost all leftover pigment from the mold area, returning it to the hopper.

“With the SSM 35 color feeding system, you waste less than 5% of expensive pigments – a huge saving for colored paver production.”

Real‑World Application – Nigerian Customer’s Interlocking Pavers

A customer from Nigeria ordered the SSM 35 specifically for producing beautiful interlocking colored pavers for a large housing project. The machine delivered:

Perfect surface texture – smooth and uniform
Vivid, long‑lasting colors – no fading or bleeding
High strength – withstood heavy truck traffic

The customer was particularly impressed by the color feeding system’s ability to produce a very soft, powder‑like pigment layer – resulting in an ultra‑smooth, almost polished paver surface.

Technical Specifications (Full)

Parameter	SSM 35 Value
Mold cavity	8‑10 blocks per cycle
Cycle time	15‑20 seconds
Main hydraulic motor	30 HP
Vibration motors	20 HP × 2
Conveyor motors	5 HP × 2
Stacker motor	10 HP
Total installed power	100 HP (75 kW) – but actual running load is 45‑50 kW
Pallet dimensions	889 × 1219 × 38 mm (standard wooden)
Product height range	50 mm – 200 mm
Mold material	Heat‑treated alloy steel
Control system	PLC + 7″ touch screen
Operation mode	Fully automatic (auto pallet + double trolley)

Why Choose Silver Steel Mills’ SSM 35?

#	Reason
1	Proven in Pakistan – Installed at CPEC motorway, DHA Multan, Nishat Power, and many more.
2	Superior mold protection – extended channel + spring dampening = longer mold life.
3	Color system saves pigment – up to 95% of color material is reused, not wasted.
4	Heat‑treated bearings – lasts longer in high‑temperature, high‑dust environments.
5	Local after‑sales support – our engineers are based in Gujranwala and Lahore; spare parts available within days.
6	Fully turnkey – we deliver, install, train your operators, and provide 3 months free service.

Comparison: SSM 35 vs. Traditional Machines

Feature	Traditional Machine	SSM 35 (Silver Steel Mills)
Color feeding system	Manual, messy, high pigment waste	Automatic, clean, <5% waste
Mold wear	High (carriage hits mold)	Low (channel extends over mold)
Bearing life	6‑12 months	18‑24 months (heat treated + springs)
Concrete waste	10‑15%	5‑8% (better cut‑off design)
Daily output (8″ blocks)	8,000‑10,000	12,000‑15,000
Power consumption	60‑70 kW	45‑50 kW (saves electricity)

Frequently Asked Questions (FAQ)

Q1: Can the SSM 35 produce only grey blocks?

Yes. The color system is optional. When not used, the machine functions as a standard high‑output block maker.

Q2: How long does it take to switch from grey to color mode?

Less than 15 minutes – attach the color hopper, load pigment, and adjust the PLC recipe.

Q3: What pigments work best?

We recommend powdered iron oxide pigments (red, yellow, black, green) mixed with white cement for best results.

Q4: Is training included?

Absolutely. Our engineers will stay at your site for 2‑3 days to train your operators on all aspects – including mold change, color recipe, and maintenance.

Q5: What is the warranty?

Structural frame: 10 years
Hydraulic components: 2 years
Motors & electronics: 1 year
Wear parts (molds, bearings, belts): available at market price (fast delivery from our stock)

Contact Silver Steel Mills Today

If you are looking to start or upgrade your paver and block production line, the SSM 35 fully automatic machine offers the best return on investment in Pakistan.

✅ Proven technology – refined over 50+ installations
✅ Color feeding system – saves you lakhs in pigment waste annually
✅ Low maintenance – heat‑treated parts and spring dampening
✅ Local support – we are just a phone call away

Government Projects Mein Approval – Kyun Zaroori Hai?

Pakistan mein government projects (CPEC, dams, highways, metro, housing schemes) mein quality standards bohat strict hain.

Project	Required Strength	Our Machine Capability
CPEC roads	5000+ PSI	✅ 7000 PSI
Diamer Bhasha Dam	6000+ PSI	✅ 7000 PSI
Metro train stations	5000+ PSI	✅ 7000 PSI
NHA highways	4000+ PSI	✅ 7000 PSI
DHA/Bahria housing	4000+ PSI	✅ 7000 PSI

Silver Steel Mills ki machines se bane blocks government labs mein test pass kar chuke hain.

Block Stacker – Aakhri Step Lekin Bahut Important

Fully automatic models mein block stacker included hai. Stacker woh system hai jo freshly made blocks ko pallets par stack karta hai aur curing area mein shift karne ke liye ready karta hai.

Stacker Ke Faide:

Benefit	Explanation
Labor bachat	2-3 mazdoor ki jagah machine kaam karegi
No damage	Machine blocks ko carefully stack karegi – toot-te nahi
Consistent stacking	Har bar same height, same alignment
Fast	Human se 3-4 times fast

SSM 35/50 mein full automatic stacker with pallet dispenser aata hai – blocks khud stack hote hain, pallets khud aate hain.

Real Case Study – Contractor Ne SSM 24 Le Kar Government Project Complete Kiya

Client: Rana Construction, Lahore
Year: 2023
Machine: SSM 24 fully automatic
Project: Government housing scheme (500 houses)

Requirement:

500,000 hollow blocks (6″ and 8″)
Quality: 5000+ PSI
Delivery timeline: 6 months

Challenge:

Manual machine se itni quantity consistent quality mein nahi bana sakte the
Government lab test pass karna zaroori tha

Solution:

SSM 24 machine purchase (85 lakh)
Automatic batching system
Planetary mixer
Digital quality control

Result:

Daily 7,000-8,000 blocks production
Lab test: 5500-6000 PSI (pass)
Project completed on time
Contractor ne 6 months mein machine ka almost 60% paisa nikal liya

Client ne kaha: “SSM 24 best machine hai. Government project ki quality bhi meet ho gayi aur production bhi fast hai. Ab doosra project aa gaya to machine lagi hi hai.”

Automatic Block Making Machine Price in Pakistan – Final Summary

Model	Type	Daily Blocks	Price (PKR)	Best For
SSM 15	Semi-Auto	4,000-5,000	45 Lakh	Startup, small business
SSM 18	Semi-Auto	5,000-6,000	48 Lakh	Growing business
SSM 24	Fully Auto	7,000-8,000	85 Lakh	Medium to large (most popular)
SSM 35	Fully Auto	10,000-12,000	1.5 Crore	Industrial scale
SSM 50	Fully Auto	15,000+	1.8 Crore	Mega scale, export

Note: SSM 24/35/50 mein batching system, planetary mixer, conveyor belt, block stacker – sab standard included hai. Price ex-factory Gujranwala. GST extra.

Why Choose Silver Steel Mills?

Reason	Explanation
7+ years experience	2018 se automatic block machines
500+ machines sold	Across Pakistan
Government approved	7000 PSI blocks – lab test pass
Complete solution	Machine + batching + mixer + conveyor + stacker
Local support	Parts available (24/7)
Warranty	1-10 years (model par depend)
Training	Operator training included
Financing	Banking partners available

FAQ – Aksar Poochay Jane Wale Sawal

Q1: Semi-automatic aur fully automatic mein kya farq hai?

Semi-auto (SSM 15/18) mein operator ko button dabana padta hai. Fully auto (SSM 24/35/50) mein machine khud chalti hai – batching, mixing, molding, stacking – sab auto.

Q2: 7000 PSI blocks waqai bante hain?

Haan. Proper raw material, batching, mixing, curing se 7000 PSI possible hai. Humare blocks government labs mein test pass kar chuke hain.

Q3: Fully automatic model mein kya kya included hai?

SSM 24/35/50 mein batching system, planetary mixer, conveyor belt, block stacker – sab kuch included hai. Aap sirf raw material dalo aur blocks ready.

Q4: Kaun sa model best hai?

SSM 24 sab se zyada bikta hai – 85 lakh mein daily 7,000-8,000 blocks. Perfect balance.

Q5: Machine kitne din mein aati hai?

30-45 days (model par depend). Installation 7-10 days.

Q6: Kya financing available hai?

Haan. Banking partners ke through loan.

Q7: Government tender ke liye machine suitable hai?

Haan. SSM 24/35/50 se bane blocks government lab pass hai. CPEC, dams, highways, housing schemes – sab mein use ho rahe hain.

Q8: Tuff tile machine alag hai kya?

Nahi. SSM series hi hai. Tuff tile mold laga do – tuff tile ban jayegi.

Conclusion – Apne Liye Sahi Automatic Machine Kaise Chune?

Pakistan mein automatic block making machine price in Pakistan bohat range mein hai. Silver Steel Mills ki machines:

Budget 45-50 lakh: SSM 15 ya SSM 18 (semi-auto)
Budget 80-90 lakh: SSM 24 (fully auto – most popular)
Budget 1.5 crore: SSM 35 (industrial)
Budget 1.8 crore: SSM 50 (mega)

Fully automatic models (SSM 24/35/50) complete system ke saath aati hain – batching, mixer, conveyor, stacker – aur 7000 PSI blocks bana sakti hain jo government projects mein approved hain.

By processing locally available raw materials—including river sand, crushed stone aggregate, cement, and industrial waste like fly ash or biomass ash—these heavy-duty machines compress and vibrate high-density solid blocks, hollow insulation blocks, interlocking tuff tiles/pavers (capable of reaching 6,000 to 7,000+ PSI), and road curbstones with absolute geometric precision.

As the country’s premier engineering house for construction machinery, Silver Steel Mills (SSM) designs, fabricates, and installs fully integrated concrete brick and paver lines. Below is a detailed technical analysis of the official SSM industrial machinery lineup, based directly on certified factory blueprints and feasibility specifications.

1. The Raw Material Recipe & Product Blueprint

To achieve premium, load-bearing quality that complies with international building codes, the automatic block machine utilizes a synchronized aggregate matrix:

Industrial Fly Ash / Biomass Ash: Acts as a highly reactive pozzolanic binder that improves the structural density, water resistance, and long-term lifespan of grey bricks.
Crushed Aggregate Dust (0mm to 5mm): Provides the structural bedrock and extreme interlocking mass required to reach high compressive strength thresholds.
River Sand: Acts as a fine aggregate filler to fill micro-voids, ensuring smooth product surfaces and sharp edges.
Portland Cement: The chemical adhesive that activates upon controlled moisture contact to secure the entire aggregate blend.

2. Official Silver Steel Mills (SSM) Machine Model Specifications

Model A: SSM 15 Auto Single-Portion Plant

An excellent entry-level solution designed for small-to-medium enterprises (SMEs), housing schemes, and localized masonry startups looking for a low capital layout.

Machine Operation System: Auto pallet and single-trolley delivery system.
Production Capacity: 100 to 110 pallets per hour.
Molding Cycle Speed: 25 to 35 seconds per compression stroke.
Pallet Product Capacity: Holds 15 Rectangular Pavers or 6 Standard Blocks per single pallet drop.
Wooden Pallet Dimensions: 650mm × 750mm × 28mm.
Supported Product Height: Flexible molding depth between 50mm to 200mm.
Total Electrical Power Grid Load: 63 HP
- Vibration Motors: 20 HP ( $10\text{ HP} \times 2$ )
- Hydraulic Pump Motor: 20 HP
- Mixer Machine Motor: 20 HP
- Conveyor Gear Motor: 3 HP

Model B: SSM 18 Brick Unified Plant (Biomass & Fly Ash Focus)

Specially engineered to handle the abrasive nature and volumetric demands of biomass ash and industrial fly ash material recipes.

Structural Composition: Manufactured using premium SS400 steel framing, solid SS chrome shafts, and Q235 MS imported sheet steel cores to resist continuous mechanical stress.
Extreme Hydraulic Compaction: Outfitted with an extraordinary 21-gallon dual pump assembly generating up to 10,000 PSI of crushing working pressure, backed by an integrated hydraulic oil cooling radiator system.
Die Mould Technology: Q235B high-grade imported hard flat bar steel shaped via precise CNC machining and top-punch engraving.
Pallet Product Capacity: Delivers 18 Interlocking Tiles or 15 High-Density Bricks per pallet drop.
Wooden Pallet Dimensions: 32 inches × 30 inches.
Material Conveyance Setup: Features an elongated 30-foot heavy-duty aggregate belt conveyor and an 8-foot automatic chain transport conveyor driven by a 3 HP gear motor.
Total Electrical Power Grid Load: 63 HP (Balanced across a 20 HP hydraulic pump, 20 HP high-amplitude vibrators, and a 20 HP compulsory mixer).

Model C: SSM 24 Double-Layer Plant (With Batching System)

The industrial standard for manufacturing premium, dual-layer interlocking tuff tiles with a vibrant, high-wear colored pigment top-coat.

Machine Operation System: Fully automatic, double-layer design featuring independent dual portion systems (one for the main grey concrete base, one for the colored pigment face).
Hydraulic Assembly: Heavy-duty imported lever control valves paired with a high-capacity hydraulic oil reservoir.
Pallet Product Capacity: Holds 24 Bricks or Interlocking Pavers per single drop cycle.
Wooden Pallet Dimensions: 30 inches × 42 inches.
Fluid & Operating Requirements: Requires a 600-liter hydraulic oil charge and 50 liters of industrial gear oil.
Total Electrical Power Grid Load: 135 HP
- Hydraulic Pump Motor: 30 HP
- Vibration Table Motors: 40 HP ( $20\text{ HP} \times 2$ )
- Mixer Machine Motors: 40 HP (30 HP Main Mixer + 10 HP Pigment Mixer)
- Stacker & Conveyor System: 15 HP (Distributed across 5 HP, 2 HP, 3 HP, 2 HP, and 3 HP gear drives)
- Batching Hopper Conveyor: 10 HP

Model D: SSM 35 Fully Automatic Double-Trolley Plant

A high-output commercial production center utilizing automated digital batching systems to achieve major output targets.

Machine Operation System: Auto pallet and synchronized double-trolley raw material delivery system.
Production Capacity: 80 to 100 pallets per hour.
Molding Cycle Speed: 20 to 30 seconds per cycle.
Pallet Product Capacity: Compresses 35 Rectangular Pavers or 35 Tuff Tiles per single stroke.
Daily Production Yield: Generates an impressive 24,000 Premium Bricks/Blocks per standard 8-hour operational shift.
Supported Product Height: 50mm to 200mm.
Fluid Requirements: Requires an 800-liter industrial hydraulic oil reservoir.
Total Electrical Power Grid Load: 131 HP
- Vibration Table Motors: 40 HP ( $20\text{ HP} \times 2$ )
- Hydraulic Pump Motor: 30 HP
- Dual Mixer Motors: 40 HP (Combined 10 kW + 30 kW setup)
- Material Conveyors: 11 HP (3 HP + 3 HP + 3 HP + 5 HP)
- Automated Product Stacker: 10 HP (5 HP + 3 HP + 2 HP)

Model E: SSM 50 Industrial Flagship Plant

The ultimate, high-capacity powerhouse manufactured by Silver Steel Mills for national mega-projects, CPEC works, and major commercial ready-mix suppliers.

Machine Operation System: Premium fully automated double-trolley layout utilizing full digital PLC touch-screen operating systems and automatic load-cell weighing scales.
Production Capacity: 80 to 100 heavy-format pallets per hour.
Molding Cycle Speed: Fast-acting 20 to 30 second compression and shake intervals.
Pallet Product Capacity: Drops 50 Rectangular Pavers or 36 Standard Concrete Bricks (Dimensions: 228mm × 110mm × 76mm) per single machine stroke.
Daily Production Yield: Delivers up to 40,000 Interlocking Pavers or Bricks in a single standard shift.
Fluid Requirements: Large-scale 800-liter hydraulic oil tank complete with an integrated forced-chiller cooling radiator system.
Total Electrical Power Grid Load: 161 HP
- Vibration Table Motors: 60 HP ( $30\text{ HP} \times 2$ deep-penetration vibration core)
- Hydraulic Pump Motor: 40 HP
- Industrial Mixer Drive: 40 HP (10 kW + 30 kW compulsory configuration)
- Material Conveyors: 11 HP
- Heavy-Duty Stacker Unit: 10 HP

3. Operational Workflow of a Turnkey Automatic Plant

To maintain high production speeds without bottlenecking, an SSM plant integrates several stages into a single continuous loop:

  [ AUTOMATED BATCHING HOPPERS ] ──> [ REINFORCED CONVEYOR ] ──> [ COMPULSORY MIXER CORE ]
                                                                             │
  [ AUTOMATED CURED STACKING ]   <── [ HYDRAULIC PRESS / MOLD ]  <─── [ OVERHEAD FEEDER ]

Digital Batching Zone: Sand, aggregate dust, and fly ash are loaded into automated batching bins. Built-in electronic load cells weigh each material precisely according to the pre-programmed mix design.
Compulsory Mixing Zone: The measured aggregates move up a heavy belt conveyor into a twin-shaft or pan mixer. Cement and water are added automatically to ensure a homogeneous, zero-slump concrete blend.
Molding & Compression Zone: The wet mix travels into the machine’s primary hopper and fills the lower die mould. The machine applies intense downward hydraulic pressure (up to 10,000 PSI) combined with high-frequency table vibration, removing all air pockets to pack the concrete tightly within seconds.
Automatic Stacking: The freshly pressed blocks travel forward on their wooden pallets into the automated stacker machine. The stacker groups the pallets vertically, making it easy for forklifts to safely transport them to the curing yard.

4. Project Feasibility: The Financial & Environmental Payback (SSM 35 Case Study)

Investing in an automated concrete block plant provides strong commercial returns compared to running an old-style clay brick kiln. Data from the SSM 35 Pre-Feasibility Study highlights the clear financial advantages for investors in Pakistan:

Daily Production Output: Based on a conservative single-shift schedule producing 24,000 fly ash bricks a day (with an estimated target of 500,000 bricks per month over 25 operational working days).
Manufacturing Cost vs. Market Value: The exact cost of production averages Rs. 12 per brick (including cement, aggregates, fly ash, labor, electrical power, and machinery depreciation). These units sell easily at a factory-gate price of Rs. 16 per brick.
Monthly Profit Profile: This margins-to-volume ratio yields a consistent net daily income of Rs. 80,000, translating to a monthly net operating income of Rs. 2,000,000.
Capital Investment Recovery: With a monthly operational budget of approximately Rs. 855,000 covering professional operators, helpers, unskilled workers, forklift/loader fuel, and scheduled field maintenance, the entire initial capital expenditure achieves a payback period of just 15 months.

Beyond strong financials, automated block plants offer full regulatory compliance. Traditional brick kilns face frequent government closures during winter smog seasons to control air pollution. SSM automated concrete block machines run on clean electrical power and generate zero toxic smoke emissions. By actively recycling industrial waste like fly ash into valuable building materials, your business remains insulated from environmental shutdowns, ensuring steady, year-round revenue.

This guide covers everything from pre-delivery oil filling to daily maintenance, mold adjustment, hydraulic system care, and common troubleshooting. Whether you’re a new operator or an experienced plant manager, this article will help you get the most out of your SSM 35.

1. Pre‑Delivery Oil Filling – Why Silver Steel Mills Does It for You

One of the most common questions we receive is about hydraulic oil filling. Many customers who buy from other suppliers receive their machine without any oil, leading to immediate damage during first use.

At Silver Steel Mills, we fill the hydraulic oil before delivery. Here’s how it works:

Oil filling point: Located at the top of the hydraulic tank (pictured below). We use a high‑grade anti‑wear hydraulic oil (ISO VG 46) suitable for Pakistan’s ambient temperatures (up to 50°C).
Filter protection: Inside the filling port, there is a built‑in filter mesh that prevents any debris from entering the hydraulic system. This extends the life of the pump, valves, and cylinders.
Why we do it: When you receive your SSM 35, it is ready to run. You don’t need to guess the oil type or quantity. We’ve already tested the system at our factory in Gujranwala.

Pro tip from Silver Steel Mills: After six months of operation, you should drain all the old hydraulic oil and replace it with fresh oil. This removes microscopic wear particles that accumulate over time.

2. Checking the Hydraulic Oil Level – The “Half‑Tube” Rule

Proper oil level is critical for the vibration system. Too little oil and the vibration box will overheat; too much oil and the vibration motors struggle to rotate.

How to check oil level on your SSM 35:

Locate the oil level indicator tube (a small transparent pipe connected to the vibration box).
The oil should reach exactly halfway up this tube.
If it’s below half, add oil slowly through the filling port.
If it’s above half, drain a small amount until it reaches the half mark.

Why half is perfect:
The vibration motors rely on the oil to both lubricate and cool internal bearings. When the oil level is exactly half, the motors rotate freely without excessive resistance. Overfilling creates hydraulic lock, causing the motors to overheat and fail prematurely.

“Some other suppliers don’t even include an oil level indicator. On the SSM 35, we’ve made it standard – because we want your machine to last.” – Senior Engineer, Silver Steel Mills

3. Belt Tension Adjustment – Avoiding Vibration Loss

Between the electric motor and the vibration box, there is a heavy‑duty V‑belt. Over time, this belt can stretch, reducing vibration force and resulting in weak blocks.

How to check belt tension on your SSM 35:

Turn off the machine and disconnect power.
Press the belt with your thumb at the midpoint between the two pulleys.
A correctly tensioned belt should deflect about 10‑15 mm (roughly the thickness of two fingers).
If it deflects more (feels loose), you need to tighten it.

How to tighten the belt:

Loosen the four mounting bolts on the electric motor base.
Turn the adjustment screw (located behind the motor) to move the motor away from the vibration box.
Retighten the motor bolts.
Recheck deflection – do not over‑tighten. An overtightened belt will damage motor bearings.

Caution: A loose belt means the vibration box receives less force, leading to poorly compacted blocks that crumble during curing. A too‑tight belt overheats the motor and shortens its life.

4. Superior Welding & Frame Strength – Why SSM 35 Outlasts Others

The SSM 35 frame is built from heat‑treated steel channels. Why is heat treatment important?

Ordinary steel channels become brittle after repeated high‑frequency vibration. Within 3‑6 months, they can crack.
Heat‑treated steel retains its strength and flexibility, lasting for years under full load.

Look at our welding:
We use double‑sided, continuous welds on all critical joints – especially the mold plate reinforcement. You’ll notice that we add two extra screw caps with locking tips to prevent the mold plate from shifting under intense vibration.

“Many customers tell us that their previous machine from another supplier broke at the welds within a year. Our SSM 35 is still running after five years – same welds, no cracks.” – Production Manager, Silver Steel Mills

5. Mold Adjustment – The 1 cm Space Rule

One of the most frequent maintenance errors is incorrect mold height adjustment. If the mold box touches the vibration platform when lowered, the vibration springs have no room to work – resulting in zero compaction.

Correct adjustment for SSM 35:

When the mold is in its lowest position, there must be a 10 mm (1 cm) gap between the bottom of the mold box and the steel platform.
This gap allows the vibration springs to oscillate freely, transferring maximum energy to the concrete mix.
Additionally, the nylon columns (five on each side) also provide an extra 10‑15 mm of vibration travel. These nylon parts are wear‑resistant and can be replaced when worn.

How to adjust the mold height:

Loosen the lock nuts on the four tie‑rods connecting the mold box to the main frame.
Turn the adjusting nuts equally on all four sides to raise or lower the mold.
Use a steel ruler to verify the 10 mm gap at both front and rear.
Retighten the lock nuts.

Important: Always keep the pallet feeder properly aligned. The wooden or steel pallet should sit flat and snug against the platform. If the pallet is warped or misaligned, the mold will not close evenly, leading to cracked blocks.

6. Column Lubrication & Copper Sleeves – Stopping Premature Wear

A common complaint with cheap block machines is that the four main columns (guide rods) wear out quickly or even break. On the SSM 35, we’ve solved this with three key design features:

6.1. Grease Points

Each column has a grease nipple at the top. You must pump high‑quality lithium grease into these nipples every week. Without grease, the metal‑on‑metal friction will rapidly wear the columns.

6.2. Copper Sleeves (Wear Rings)

Inside the upper and lower bushing housings, we install copper sleeves. Copper is self‑lubricating and much softer than steel, so it wears instead of the expensive column. When the copper sleeve wears out (usually after 2‑3 years), you simply replace the sleeve – not the entire column.

Many other manufacturers skip these copper sleeves to save cost. Their columns then grind directly against the steel housing, causing deep scoring and eventual breakage.

6.3. Balance System – Four Columns Moving in Sync

The SSM 35 is equipped with a mechanical balance mechanism (a steel rack‑and‑pinion system) that forces all four columns to rise and fall at the same speed. This eliminates uneven loading that would otherwise cause one column to wear faster.

“Without a balance system, the mold box can tilt, putting all the stress on one column. That column then snaps – and your production stops for weeks.” – Field Service Engineer, Silver Steel Mills

7. Hydraulic Cylinder & Sensor Position – Troubleshooting “Can’t Lift” Errors

Some operators report that their block machine’s hydraulic cylinder won’t lift the mold box, even though the pump is running. Most often, this is due to a sensor position problem, not a hydraulic failure.

The SSM 35 has a computerized protection system (PLC) that monitors the position of all hydraulic cylinders. If any cylinder is not at its “home” (original) position, the machine will not execute the next command – preventing accidental damage.

7.1. Pallet Feeder Cylinder Sensor

There is a sensor at the back of the pallet feeder cylinder. When the cylinder is fully retracted (home position), a metal flag trips this sensor, and its indicator light turns on.
If this sensor is not lit, the machine thinks the pallet feeder is still forward, and it will not allow the mold to come down.

Fix: Manually retract the pallet feeder cylinder (using the manual override button on the PLC panel) until the sensor light turns on.

7.2. Material Cut-Off Cylinder Sensor

Similarly, the cylinder that controls the material hopper gate has a rear sensor. When the gate is fully closed (home position), that sensor must be lit.
If not lit, the machine will not start the pressing cycle.

7.3. Main Press Cylinder Sensor

The main press cylinder (which pushes down the mold) also has an upper sensor (fully retracted position). The mold will only rise if this sensor is active.

Why this is a benefit, not a bug:
This sensor network prevents operators from accidentally starting a cycle when the machine is not properly set up. It saves you from broken molds, damaged cylinders, and injuries.

8. Daily & Weekly Maintenance Checklist for SSM 35

To keep your SSM 35 running at peak performance, follow this simple schedule:

Frequency	Task
Daily (start of shift)	Check oil level in the vibration box (half‑tube rule). Grease all four column nipples (3‑5 pumps each). Inspect belts for wear and proper tension.
Daily (end of shift)	Clean excess concrete from mold, platform, and pallet feeder. Blow off dust from electrical panel (use low‑pressure air).
Weekly	Check all hydraulic hoses for leaks. Tighten any loose bolts on the mold, frame, and motor mounts. Inspect copper sleeves for wear.
Monthly	Change the hydraulic oil filter element. Test all limit switches and sensors. Lubricate roller chains on the conveyor.
Every 6 months	Drain and replace hydraulic oil (200 liters). Replace vibration motor belts. Check mold plate for flatness.
Yearly	Replace copper sleeves. Overhaul hydraulic pump (check seals). Recalibrate load cells (if batching system installed).

9. Why Pakistani Contractors Choose Silver Steel Mills SSM 35

Built for local conditions: Our machines handle power fluctuations, high ambient temperatures, and dusty environments.
Local spare parts stock: We keep all wear parts (copper sleeves, belts, seals, sensors) at our Gujranwala warehouse. No waiting for imports.
On‑site training: Our technicians travel to your site for installation and operator training.
Proven references: SSM 35 machines are working at DHA Multan, Nishat Power (Lahore), CPEC motorway sites (CSCEC), and many housing schemes.

10. Common Problems and Their Solutions (Troubleshooting)

Problem	Likely Cause	Solution (from Silver Steel Mills)
Weak blocks, crumbling edges	Loose V‑belt or low oil level	Tighten belt; check oil half‑tube level.
Mold box will not lift	Pallet feeder sensor not triggered	Manually retract pallet cylinder until sensor lights.
Excessive noise from vibration box	Low oil or old oil	Top up or replace hydraulic oil.
Columns wear quickly	No grease or missing copper sleeves	Grease weekly; install genuine copper sleeves (we stock them).
Hydraulic pump runs but no pressure	Worn pump seals or clogged suction filter	Replace seals; clean or replace filter.
Machine cycles but mold doesn’t press down	Material cut‑off cylinder not at home position	Close gate manually until sensor lights.

5. Partner with Pakistan’s Trusted Machinery Experts

Investing in automated block machinery is a major, long-term business decision. Partnering with an experienced local manufacturer like Silver Steel Mills gives you a clear competitive advantage:

World-Class Engineering, Local Prices: We handle all structural cutting, heavy hydraulic assembly, and electrical control panel programming in-house, allowing us to offer high-output, durable plant setups at a fraction of the cost of expensive imported foreign machinery.
Immediate Local Spare Parts Support: You never have to worry about long customs delays or dealing with overseas suppliers for basic maintenance. We keep a complete inventory of certified replacement parts—including custom CNC molds, replacement conveyor rollers, load cells, and hydraulic seals—right here in Pakistan for rapid support.

What Are Automatic Block Making Machines?

Automatic block making machines automate the entire concrete block production process. Equipped with the latest technology, they minimize manual labor and produce blocks that are uniform in size, shape, and strength. These machines can manufacture various types of concrete products, including solid blocks, hollow blocks, interlocking tiles, and paving stones.

At Silver Steel Mills (SSM), we provide a diverse lineup of automatic block making machines designed to meet different production demands. Our machines incorporate features like hydraulic pressure systems, automated control panels, and powerful vibration motors to guarantee superior block quality.

Factors That Affect Automatic Block Making Machine Prices in Pakistan

The cost of an automatic block making machine depends on multiple factors. Understanding these helps buyers make informed choices:

Production Capacity: Machines with higher output per hour or day are priced higher. SSM offers models suited for small to large-scale production.
Machine Features: Advanced features such as PLC controls, automatic material feeders, and hydraulic systems increase the cost but boost efficiency and output.
Brand Reliability: As a trusted name in Pakistan’s machinery market, Silver Steel Mills delivers durable and reliable machines, reflecting in their pricing.
Customization: Options like special mold designs and machine size variations tailored to customer needs can impact the final price.
Raw Material Compatibility: SSM machines are designed to handle different raw materials such as cement, sand, and aggregates, offering flexibility in manufacturing.
Automation Level: Fully automatic machines cost more than semi-automatic or manual ones, due to their enhanced performance and reduced labor needs.

Why Choose Silver Steel Mills for Your Block Making Machines?

Selecting the right manufacturer is crucial for long-term success. Here’s why Silver Steel Mills stands out:

Cutting-Edge Technology

Our machines are engineered with the latest technology, including advanced automation and hydraulic systems. This ensures faster production with consistent block quality, requiring minimal human intervention.

Tailored Solutions

We understand every business has unique requirements. That’s why we offer customizable machines, whether you need higher production volumes or versatility in block types.

Robust Build and Longevity

Silver Steel Mills machines are constructed from high-quality materials, built to withstand continuous heavy-duty operation and deliver reliable performance over years.

Comprehensive After-Sales Support

Purchasing from SSM means access to expert installation, training, and maintenance support, ensuring your machine operates optimally with minimal downtime.

Price Range of Automatic Block Making Machines in Pakistan

The prices vary based on capacity and features:

Entry-Level Machines: Starting around PKR 2,500,000, these are ideal for small businesses with basic production needs.
Mid-Range Machines: Costing between PKR 5,000,000 to PKR 10,000,000, these offer higher capacities and enhanced features like automatic feeding and hydraulic presses.
High-End Machines: Designed for large-scale production, these can exceed PKR 15,000,000, incorporating full automation and custom options.

Silver Steel Mills offers machines across these ranges to accommodate all business scales and budgets.

Benefits of Investing in Automatic Block Making Machines

Boosted Productivity: Significantly increase block output with faster cycle times.
Consistent Quality: Produce uniform blocks that meet construction standards.
Cost Efficiency: Save on labor costs and reduce waste with precise automation.
Reduced Labor Dependency: Automation minimizes manual work, allowing efficient workforce management.
Product Variety: Easily manufacture different block types using the same machine.

Where to Purchase Automatic Block Making Machines in Pakistan?

Silver Steel Mills is a leading supplier of automatic block making machines with a strong reputation for quality and support. Visit silversteelmills.com to explore the range and request personalized quotes.

While local dealers and online platforms like OLX may offer used machines, purchasing directly from a reputable manufacturer like Silver Steel Mills ensures you receive genuine products with warranty and after-sales service.

The Expanding Concrete Block Industry in Pakistan and the Role of Automatic Block Making Machines

Pakistan’s construction industry is experiencing unprecedented growth due to rapid urbanization, infrastructure development, and housing demands. This surge has led to a substantial increase in the need for reliable, durable, and cost-effective building materials, with concrete blocks being one of the most widely used.

Concrete blocks offer excellent structural integrity, thermal insulation, and fire resistance, making them a preferred choice in both residential and commercial construction. Consequently, the manufacturing sector for these blocks is also growing, demanding machinery that can keep up with large volumes, maintain quality, and reduce production costs.

Automatic block making machines are the backbone of modern block manufacturing businesses. By automating the production process, these machines not only increase the speed of production but also guarantee consistent quality, reduce labor dependency, and lower overall operational costs.

What Are Automatic Block Making Machines and How Do They Work?

Automatic block making machines are sophisticated pieces of equipment designed to automate the entire concrete block production process. These machines operate by compressing a carefully mixed concrete slurry into molds using hydraulic pressure and vibration technology to form high-strength blocks.

Key components typically include:

Hydraulic Pressure System: Applies the necessary force to compact concrete mix uniformly.
Vibration Motors: Enhance concrete compaction and remove air pockets, increasing block density and strength.
Control Panels: Automated or PLC-based systems that regulate machine functions, cycle times, and production parameters.
Material Feeding System: Automatically delivers raw materials into the mixing and molding area, reducing manual intervention.

At Silver Steel Mills (SSM), our machines are engineered for precision and efficiency. Our range supports production of a variety of concrete products such as:

Solid blocks for walls and foundations
Hollow blocks for lightweight structures and insulation
Interlocking pavers used in flooring and landscaping
Tuff tiles and decorative blocks

Detailed Factors Affecting the Price of Automatic Block Making Machines in Pakistan

Investing in an automatic block making machine requires understanding several factors influencing cost:

1. Production Capacity

This is a critical consideration. Machines designed to produce thousands of blocks per day will naturally cost more due to heavier duty parts, larger molds, and advanced automation.

Low Capacity Models: Suitable for startups or small manufacturers, producing 500-1000 blocks/day.
Medium Capacity Models: Can produce 1500-3000 blocks/day, ideal for growing businesses.
High Capacity Models: Capable of producing 5000+ blocks/day, built for large-scale commercial manufacturing.

Silver Steel Mills offers tailored machines within all these capacities, allowing clients to choose according to their business scale.

2. Machine Features and Automation

More sophisticated features add to the price but improve productivity and ease of operation:

PLC Control Panels: Provide precise control over each production step, enabling remote monitoring and troubleshooting.
Automatic Feeding and Material Distribution: Reduces material wastage and increases operational speed.
Hydraulic Presses: Ensure consistent block compaction, improving strength.
Multi-Mold Capabilities: Allow switching between different block types quickly.

SSM’s advanced models incorporate these technologies to maximize output and quality.

3. Material Compatibility and Versatility

Our machines are designed to handle a wide range of raw materials — including cement, sand, crushed stone, and industrial by-products like fly ash — giving manufacturers flexibility to adapt based on local material availability and cost.

4. Customization Options

Customization can include:

Mold size and shape
Machine footprint to fit factory space
Specific automation modules
Integration with conveyor belts or packaging lines

These customizations add value but may increase the initial cost.

5. Brand Trust and After-Sales Service

Investing in a machine from a reputed brand like Silver Steel Mills guarantees quality components, adherence to safety and manufacturing standards, and reliable technical support. This reduces downtime and maintenance costs, justifying a higher upfront price.

Why Silver Steel Mills Should Be Your Preferred Manufacturer

Choosing a machine supplier is as important as choosing the machine itself. Here’s why Silver Steel Mills (SSM) leads the market in Pakistan:

Innovative Engineering: Our R&D team continuously integrates the latest global innovations in automation and mechanical design into our machines.
Robust Construction: Machines are manufactured from high-grade steel and quality components to endure tough factory environments and long production hours.
Energy Efficiency: SSM machines are designed to consume less power without compromising performance, reducing operational costs.
Flexible Financing: Understanding the capital constraints of many businesses, we offer flexible payment plans and leasing options.
Full Lifecycle Support: From consultation, installation, operator training to routine maintenance, our dedicated support team ensures smooth operations.

Comprehensive Price Overview of Automatic Block Making Machines in Pakistan

Here is a more detailed look at the price spectrum:

Machine Type	Approximate Price (PKR)	Features & Capacity
Basic Automatic Machines	2,500,000 – 4,500,000	Suitable for low-volume, semi-automated production
Mid-Range Automatic Machines	5,000,000 – 10,000,000	Fully automated, hydraulic press, higher output
High-End Fully Automatic	10,000,000 – 20,000,000+	Large-scale production, multi-mold, PLC control

Prices vary depending on specific requirements, optional accessories, and any customizations.

Key Benefits of Using Automatic Block Making Machines

Scalability: Easily ramp up production to meet growing market demand.
Consistent Product Quality: High compression and vibration ensure blocks meet structural and aesthetic standards.
Labor Savings: Automated feeding and molding significantly reduce labor costs.
Waste Reduction: Precise material handling minimizes raw material wastage.
Product Range: Quickly switch between different block designs and sizes to diversify product offerings.
Improved Profit Margins: Faster production and reduced defects lead to better profitability.

Where and How to Buy Automatic Block Making Machines in Pakistan?

When sourcing machines, prioritize verified manufacturers like Silver Steel Mills to ensure:

Authentic equipment with warranties
Access to genuine spare parts
Professional installation and training
Ongoing technical assistance
Agar aap Pakistan mein construction business shuru karne ka soch rahe hain ya apne purane manual setup ko upgrade karna chahte hain, toh Automatic Block Making Machines aaj kal ki sabse badi zaroorat hain.
Manual tareeqay se block banana ab na sirf mehnga parta hai balkay us mein labor ke maslay aur quality ki consistency ka bhi bara challenge hota hai. Silver Steel Mills mein humne dekha hai ke jo log technology par shift ho rahe hain, wahi market mein survive kar pa rahe hain.
Is guide mein hum baat karenge ke Pakistan mein in machines ki price kya hai, inka business model kaise kaam karta hai aur aapko apne setup ke liye sahi machine kaise choose karni chahiye.
1. Pakistan Mein Automatic Block Machine Ki Price Kya Hai?
Sabse pehle us sawal par aate hain jo har investor poochta hai: Price kya hogi?
Pakistan mein automatic block making machine ki price fix nahi hoti, kyunke ye modular hoti hain. Phir bhi, aik andaze ke liye:
- Semi-Automatic Setup: Rs. 15 Lakh se 25 Lakh tak.
- Fully Automatic (Hydraulic) Setup: Rs. 35 Lakh se shuru ho kar 80 Lakh+ tak ja sakta hai (capacity aur components ke mutabiq).
Price kin cheezon par depend karti hai?
1. Production Capacity: Aik shift (8 ghante) mein machine kitne blocks banati hai (e.g., 2000 vs 5000 blocks).
2. Automation Level: Kya machine khud material uthati hai (Auto-batching) ya labor ki zaroorat hai?
3. Pressure Capacity: High-density blocks ke liye zyada tonnage wala hydraulic system mehnga hota hai.
4. Local vs Imported Parts: Silver Steel Mills jese standards mein hum heavy-duty local fabrication ke saath branded motors aur valves use karte hain taake durability miley.
2. Business Model: Profit Aur Production
Automatic machine lagane ka sabse bada faida Speed aur Accuracy hai. Jab machine automatic hoti hai, toh har block ka size aur mazbooti aik jesi hoti hai, jo bade contractors aur developers ki pehli shart hoti hai.
Raw Material Ka Kharcha
Pakistan mein aam taur par ye material use hota hai:
- Crush (Bajri): 0-pala ya sargodha crush.
- Sand (Rait): Ravi ya Chenab ki rait.
- Cement: Lucky, Bestway ya DG Cement.
- Chemical (Optional): Strength aur finish behtar karne ke liye.
Profit Margin
Agar aap din ke 3000 blocks banate hain aur aik block par Rs. 5 se 10 ka net profit bacha rahe hain, toh aap mahana lakhon rupay kama sakte hain. Is mein labor cost kam ho jati hai kyunke machine ka kaam fast hota hai.
3. Silver Steel Mills Ki Expert Advice: Machine Lete Waqt Kya Dekhen?
Sirf sasti machine ke peeche mat bhagain. Industrial kaam mein “Down-time” (machine kharab hona) sabse bada nuksan hai.
1. Hydraulic System: Check karen ke pumps aur valves kis brand ke hain. Leakage ka masla nahi hona chahiye.
2. Frame Ki Mazbooti: Machine ka loha (Steel) heavy-duty hona chahiye taake vibration se cracks na ayein.
3. Vibration Technology: Achi machine wahi hai jo material ko sahi tarah se settle kare taake block andar se porus (khokhla) na rahe.
4. After-Sales Service: Kya manufacturer ke paas spare parts aur mechanic maujood hain?
4. Automatic Machine Lagane Ke Fayde
- Labor Ki Kam Zaroorat: Jahan manual kaam mein 10-12 bande chahiye hote hain, automatic setup 3-4 bandon se chal jata hai.
- Zero Wastage: Material ka zaya hona khatam ho jata hai.
- Multi-Purpose: Aik hi machine par aap 4-inch, 6-inch, 8-inch blocks aur yahan tak ke Paver Tiles aur Curbs Stones bhi bana sakte hain sirf die (mould) change karke.
5. Frequently Asked Questions (FAQs)
Q1: Kya is machine ke liye commercial bijli ka connection chahiye? Ji haan, aksar automatic machines 3-phase connection par chalti hain kyunke inki motors heavy hoti hain.
Q2: Aik machine ki life kitni hoti hai? Agar Silver Steel Mills jesi achi quality ki machine ho aur proper oiling/maintenance ki jaye, toh ye 10-15 saal aram se nikaal jati hai.
Q3: Kya naye bande ke liye ye business mushkil hai? Nahi, hum machine install karne ke saath saath aapke staff ko training bhi dete hain ke machine kaise chalani hai aur material ka ratio kya rakhna hai.
Conclusion
Pakistan ka construction sector grow kar raha hai aur saste gharon ki demand ki wajah se blocks ki market kabhi khatam nahi hogi. Silver Steel Mills aapko na sirf machine provide karta hai balkay aik poora business solution deta hai.